lkml.org 
[lkml]   [2017]   [Jul]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [linux-sunxi] [PATCH 2/3] arm64: allwinner: a64: enable AXP803 for Banana Pi M64
From


于 2017年7月23日 GMT+08:00 下午11:15:04, Chen-Yu Tsai <wens@csie.org> 写到:
>On Fri, Jul 21, 2017 at 7:38 PM, <icenowy@aosc.io> wrote:
>> 在 2017-07-21 15:49,Chen-Yu Tsai 写道:
>>>
>>> On Fri, Jul 21, 2017 at 3:44 PM, Icenowy Zheng <icenowy@aosc.io>
>wrote:
>>>>
>>>>
>>>>
>>>> 于 2017年7月21日 GMT+08:00 下午3:42:07, Chen-Yu Tsai <wens@csie.org> 写到:
>>>>>
>>>>> On Fri, Jul 21, 2017 at 7:07 AM, Icenowy Zheng <icenowy@aosc.io>
>wrote:
>>>>>>
>>>>>> Banana Pi M64 board uses an AXP803 PMIC.
>>>>>>
>>>>>> Enable the PMIC and its regulators.
>>>>>>
>>>>>> As we have now proper regulators support, missing or dummy
>regulators
>>>>>> are changed to the correct ones.
>>>>>>
>>>>>> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
>>>>>> ---
>>>>>> .../boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 116
>>>>>
>>>>> +++++++++++++++++++--
>>>>>>
>>>>>> 1 file changed, 106 insertions(+), 10 deletions(-)
>>>>>>
>>>>>> diff --git
>>>>>
>>>>> a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
>>>>> b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
>>>>>>
>>>>>> index 829922d077fb..51d67c0a0edf 100644
>>>>>> --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
>>>>>> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
>>>>>> @@ -58,13 +58,6 @@
>>>>>> chosen {
>>>>>> stdout-path = "serial0:115200n8";
>>>>>> };
>>>>>> -
>>>>>> - reg_vcc3v3: vcc3v3 {
>>>>>> - compatible = "regulator-fixed";
>>>>>> - regulator-name = "vcc3v3";
>>>>>> - regulator-min-microvolt = <3300000>;
>>>>>> - regulator-max-microvolt = <3300000>;
>>>>>> - };
>>>>>> };
>>>>>>
>>>>>> &ehci1 {
>>>>>> @@ -76,6 +69,7 @@
>>>>>> pinctrl-0 = <&rgmii_pins>;
>>>>>> phy-mode = "rgmii";
>>>>>> phy-handle = <&ext_rgmii_phy>;
>>>>>> + phy-supply = <&reg_dc1sw>;
>>>>>> status = "okay";
>>>>>> };
>>>>>>
>>>>>> @@ -99,7 +93,7 @@
>>>>>> &mmc0 {
>>>>>> pinctrl-names = "default";
>>>>>> pinctrl-0 = <&mmc0_pins>;
>>>>>> - vmmc-supply = <&reg_vcc3v3>;
>>>>>> + vmmc-supply = <&reg_dcdc1>;
>>>>>> cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
>>>>>> cd-inverted;
>>>>>> disable-wp;
>>>>>> @@ -110,7 +104,8 @@
>>>>>> &mmc1 {
>>>>>> pinctrl-names = "default";
>>>>>> pinctrl-0 = <&mmc1_pins>;
>>>>>> - vmmc-supply = <&reg_vcc3v3>;
>>>>>> + vmmc-supply = <&reg_dldo2>;
>>>>>> + vqmmc-supply = <&reg_dldo4>;
>>>>>> bus-width = <4>;
>>>>>> non-removable;
>>>>>> status = "okay";
>>>>>> @@ -119,7 +114,7 @@
>>>>>> &mmc2 {
>>>>>> pinctrl-names = "default";
>>>>>> pinctrl-0 = <&mmc2_pins>;
>>>>>> - vmmc-supply = <&reg_vcc3v3>;
>>>>>> + vmmc-supply = <&reg_dcdc1>;
>>>>>> bus-width = <8>;
>>>>>> non-removable;
>>>>>> cap-mmc-hw-reset;
>>>>>> @@ -130,6 +125,107 @@
>>>>>> status = "okay";
>>>>>> };
>>>>>>
>>>>>> +&r_rsb {
>>>>>> + status = "okay";
>>>>>> +
>>>>>> + axp803: pmic@3a3 {
>>>>>> + compatible = "x-powers,axp803";
>>>>>> + reg = <0x3a3>;
>>>>>> + interrupt-parent = <&r_intc>;
>>>>>> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
>>>>>> + };
>>>>>> +};
>>>>>> +
>>>>>> +#include "axp803.dtsi"
>>>>>> +
>>>>>> +&reg_aldo2 {
>>>>>> + regulator-always-on;
>>>>>> + regulator-min-microvolt = <1800000>;
>>>>>> + regulator-max-microvolt = <3300000>;
>>>>>> + regulator-name = "vcc-pl";
>>>>>> +};
>>>>>> +
>>>>>> +&reg_aldo3 {
>>>>>> + regulator-always-on;
>>>>>> + regulator-min-microvolt = <3000000>;
>>>>>> + regulator-max-microvolt = <3000000>;
>>>>>> + regulator-name = "vcc-pll-avcc";
>>>>>> +};
>>>>>> +
>>>>>> +&reg_dc1sw {
>>>>>> + regulator-name = "vcc-phy";
>>>>>> +};
>>>>>> +
>>>>>> +&reg_dcdc1 {
>>>>>> + regulator-always-on;
>>>>>> + regulator-min-microvolt = <3300000>;
>>>>>> + regulator-max-microvolt = <3300000>;
>>>>>> + regulator-name = "vcc-3v3";
>>>>>> +};
>>>>>> +
>>>>>> +&reg_dcdc2 {
>>>>>> + regulator-always-on;
>>>>>> + regulator-min-microvolt = <1000000>;
>>>>>
>>>>>
>>>>> The datasheet says the minimum voltage is 1.04V.
>>>>
>>>>
>>>> A64 datasheet?
>>>
>>>
>>> Yes. V1.1.
>>>
>>>>
>>>> Maybe I need to fix all A64 AXP patches.
>>>>
>>>>>
>>>>>> + regulator-max-microvolt = <1300000>;
>>>>>> + regulator-name = "vdd-cpux";
>>>>>> +};
>>>>>> +
>>>>>> +/* DCDC3 is polyphased with DCDC2 */
>>>>>> +
>>>>>> +&reg_dcdc5 {
>>>>>> + regulator-always-on;
>>>>>> + regulator-min-microvolt = <1500000>;
>>>>>> + regulator-max-microvolt = <1500000>;
>>>>>> + regulator-name = "vcc-dram";
>>>>>> +};
>>>>>> +
>>>>>> +&reg_dcdc6 {
>>>>>> + regulator-always-on;
>>>>>> + regulator-min-microvolt = <1100000>;
>>>>>> + regulator-max-microvolt = <1100000>;
>>>>>> + regulator-name = "vdd-sys";
>>>>>> +};
>>>>>> +
>>>>>> +&reg_dldo1 {
>>>>>> + regulator-min-microvolt = <3300000>;
>>>>>> + regulator-max-microvolt = <3300000>;
>>>>>> + regulator-name = "vcc-hdmi-dsi";
>>>>>> +};
>>>>>> +
>>>>>> +&reg_dldo2 {
>>>>>> + regulator-min-microvolt = <3300000>;
>>>>>> + regulator-max-microvolt = <3300000>;
>>>>>> + regulator-name = "vcc-wifi";
>>>>>> +};
>>>>>> +
>>>>>> +&reg_dldo4 {
>>>>>> + regulator-min-microvolt = <1800000>;
>>>>>> + regulator-max-microvolt = <3300000>;
>>>>>> + regulator-name = "vcc-wifi-io";
>>>>>> +};
>>>>>> +
>>>>>> +&reg_eldo1 {
>>>>>> + regulator-min-microvolt = <1800000>;
>>>>>> + regulator-max-microvolt = <1800000>;
>>>>>> + regulator-name = "cpvdd";
>>>>>> +};
>>>>>> +
>>>>>
>>>>>
>>>>> It looks like you are missing a few regulators? I assume you
>>>>> would add them once the peripherals that use them are added?
>>>>
>>>>
>>>> Yes.
>>>>
>>>> I mainly dropped CSI part, as it seems so complicate.
>>>
>>>
>>> HSIC is also missing. I know the board doesn't use the feature,
>>> but the regulator is hooked up. It would be better to set the
>>> name and constraints.
>>
>>
>> OK.
>>
>> I think maybe Pine64 and SoPine w/ baseborad also need the HSIC
>> regulator set up, right? (They're also not used but hooked)
>>
>
>Correct. If they are wired up, then they have constraints that
>need to be adhered to.

Already fixed up in Pine64/SoPine patchset v2.

>
>ChenYu
>
>>>
>>> ChenYu
>>>
>>>>
>>>>>
>>>>> Otherwise this patch looks good.
>>>>>
>>>>> ChenYu
>>>>>
>>>>>> +/*
>>>>>> + * The A64 chip cannot work without this regulator off, although
>>>>>> + * it seems to be only driving the AR100 core.
>>>>>> + * Maybe we don't still know well about CPUs domain.
>>>>>> + */
>>>>>> +&reg_fldo2 {
>>>>>> + regulator-always-on;
>>>>>> + regulator-min-microvolt = <1100000>;
>>>>>> + regulator-max-microvolt = <1100000>;
>>>>>> + regulator-name = "vdd-cpus";
>>>>>> +};
>>>>>> +
>>>>>> +&reg_rtc_ldo {
>>>>>> + regulator-name = "vcc-rtc";
>>>>>> +};
>>>>>> +
>>>>>> &uart0 {
>>>>>> pinctrl-names = "default";
>>>>>> pinctrl-0 = <&uart0_pins_a>;
>>>>>> --
>>>>>> 2.13.0
>>>>>>
>>>>>> --
>>>>>> You received this message because you are subscribed to the
>Google
>>>>>
>>>>> Groups "linux-sunxi" group.
>>>>>>
>>>>>> To unsubscribe from this group and stop receiving emails from it,
>>>>>
>>>>> send an email to linux-sunxi+unsubscribe@googlegroups.com.
>>>>>>
>>>>>> For more options, visit https://groups.google.com/d/optout.
>>>>
>>>>
>>>> --
>>>> You received this message because you are subscribed to the Google
>Groups
>>>> "linux-sunxi" group.
>>>> To unsubscribe from this group and stop receiving emails from it,
>send an
>>>> email to linux-sunxi+unsubscribe@googlegroups.com.
>>>> For more options, visit https://groups.google.com/d/optout.
>>>
>>>
>>> _______________________________________________
>>> linux-arm-kernel mailing list
>>> linux-arm-kernel@lists.infradead.org
>>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>>
>>
>> --
>> You received this message because you are subscribed to the Google
>Groups
>> "linux-sunxi" group.
>> To unsubscribe from this group and stop receiving emails from it,
>send an
>> email to linux-sunxi+unsubscribe@googlegroups.com.
>> For more options, visit https://groups.google.com/d/optout.
>
>_______________________________________________
>linux-arm-kernel mailing list
>linux-arm-kernel@lists.infradead.org
>http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

\
 
 \ /
  Last update: 2017-07-23 17:40    [W:1.073 / U:0.012 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site