lkml.org 
[lkml]   [2017]   [Jun]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v9 0/3] Support for USB DRD PHY driver for NS2
From
Date
Hi,

On Friday 09 June 2017 05:12 PM, Raviteja Garimella wrote:
> Changes in V9:
> =============
> Rebased on linux-phy next. Driver files and Kconfig/Makefile
> changes now in drivers/phy/broadcom.

merged the _phy_ patches to linux-phy. Thanks for doing multiple revisions to
get it merged.

-Kishon
>
> Changes in v8:
> =============
> -Renamed phy shutdown routine
> -Used devm_request_irq in stead of threaded irq
> -Removed devm_unregister calls in probe routine
>
> Changes in v7:
> =============
> Cleaned up unused variables in phy private data structure that's
> missed out in v6.
> Setting of phy mode to device/host is removed from phy power on.
> routine.
>
> Changes in v6:
> =============
> Removed spin locks which are not required as the references
> to phy_ops in the same driver were removed in v5.
>
> Removed host/device 'notify' routines which are registered
> using 'extcon_register_notifier'. The irq handler is sufficient
> to deal with the change in extcon events within the same driver.
>
> Changes in v5:
> =============
> Removed references to phy_ops in the same driver by connect_work
> event handler to change the phy modes.
>
> To support dynamically changing the mode of the phy, it does
> not require doing a phy reset/programming of PHY PLL. Changes
> are made to the connect_work routine to just program the required
> register bits to achieve this purpose.
>
> Changes in v4:
> =============
> Remove references to edev->name in debug prints.
>
> Changes in v3:
> =============
> Remove unnecessary checks for poweron as suggested in review.
>
> Changes in v2:
> =============
> 1. Initialize file operations .owner field with THIS_MODULE.
> 2. Remove unnecessary gpio example in DT bindings documentation.
> This is previously acked by Rob Herring <robh@kernel.org>
>
> Introduction for PATCH v1:
>
> This patch adds support for USB Dual Role Device Phy for Broadcom
> Northstar2 SoC. Apart from the new phy driver, this patchset contains
> changes to Kconfig, Makefile, and Device tree files.
>
> This patchset is tested on Broadcom NS2 BCM958712K reference board.
>
> Raviteja Garimella (3):
> dt-bindings: phy: Add DT bindings documentation for NS2 USB DRD PHY
> phy: phy-bcm-ns2-usbdrd: Broadcom USB DRD PHY driver for Northstar2
> arm64: dts: NS2: Add USB DRD PHY device tree node
>
> .../devicetree/bindings/phy/brcm,ns2-drd-phy.txt | 30 ++
> arch/arm64/boot/dts/broadcom/ns2.dtsi | 14 +
> drivers/phy/broadcom/Kconfig | 13 +
> drivers/phy/broadcom/Makefile | 1 +
> drivers/phy/broadcom/phy-bcm-ns2-usbdrd.c | 437 +++++++++++++++++++++
> 5 files changed, 495 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt
> create mode 100644 drivers/phy/broadcom/phy-bcm-ns2-usbdrd.c
>

\
 
 \ /
  Last update: 2017-06-12 01:47    [W:0.051 / U:0.024 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site