lkml.org 
[lkml]   [2017]   [Jun]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v8 0/3] Support for USB DRD PHY driver for NS2
From
Date
Hi,

On Friday 09 June 2017 02:30 PM, Raviteja Garimella wrote:
> Hi,
>
> On Fri, Jun 9, 2017 at 2:25 PM, Kishon Vijay Abraham I <kishon@ti.com> wrote:
>> Hi,
>>
>> On Thursday 08 June 2017 04:05 PM, Raviteja Garimella wrote:
>>> Changes in v8:
>>> =============
>>> -Renamed phy shutdown routine
>>> -Used devm_request_irq in stead of threaded irq
>>
>> That's not what I intended. Continue to use threaded irq but remove delayed work.
>>
>
> Yes I get that. We see intermittent connection issues without delayed
> work. Debounce delay matters there.

All right!

I'm unable to apply the series. Please rebase to linux-phy next (directory
structure has changed)

Thanks
Kishon
>
> Thanks,
> Ravi
>
>> Thanks
>> Kishon
>>> -Removed devm_unregister calls in probe routine
>>>
>>> Changes in v7:
>>> =============
>>> Cleaned up unused variables in phy private data structure that's
>>> missed out in v6.
>>> Setting of phy mode to device/host is removed from phy power on.
>>> routine.
>>>
>>> Changes in v6:
>>> =============
>>> Removed spin locks which are not required as the references
>>> to phy_ops in the same driver were removed in v5.
>>>
>>> Removed host/device 'notify' routines which are registered
>>> using 'extcon_register_notifier'. The irq handler is sufficient
>>> to deal with the change in extcon events within the same driver.
>>>
>>> Changes in v5:
>>> =============
>>> Removed references to phy_ops in the same driver by connect_work
>>> event handler to change the phy modes.
>>>
>>> To support dynamically changing the mode of the phy, it does
>>> not require doing a phy reset/programming of PHY PLL. Changes
>>> are made to the connect_work routine to just program the required
>>> register bits to achieve this purpose.
>>>
>>> Changes in v4:
>>> =============
>>> Remove references to edev->name in debug prints.
>>>
>>> Changes in v3:
>>> =============
>>> Remove unnecessary checks for poweron as suggested in review.
>>>
>>> Changes in v2:
>>> =============
>>> 1. Initialize file operations .owner field with THIS_MODULE.
>>> 2. Remove unnecessary gpio example in DT bindings documentation.
>>> This is previously acked by Rob Herring <robh@kernel.org>
>>>
>>> Introduction for PATCH v1:
>>>
>>> This patch adds support for USB Dual Role Device Phy for Broadcom
>>> Northstar2 SoC. Apart from the new phy driver, this patchset contains
>>> changes to Kconfig, Makefile, and Device tree files.
>>>
>>> This patchset is tested on Broadcom NS2 BCM958712K reference board.
>>>
>>> Repo: https://github.com/Broadcom/arm64-linux.git
>>> Branch: ns2_drdphy_v8
>>>
>>> Raviteja Garimella (3):
>>> dt-bindings: phy: Add DT bindings documentation for NS2 USB DRD PHY
>>> phy: phy-bcm-ns2-usbdrd: Broadcom USB DRD PHY driver for Northstar2
>>> arm64: dts: NS2: Add USB DRD PHY device tree node
>>>
>>> .../devicetree/bindings/phy/brcm,ns2-drd-phy.txt | 30 ++
>>> arch/arm64/boot/dts/broadcom/ns2.dtsi | 14 +
>>> drivers/phy/Kconfig | 13 +
>>> drivers/phy/Makefile | 1 +
>>> drivers/phy/phy-bcm-ns2-usbdrd.c | 437 +++++++++++++++++++++
>>> 5 files changed, 495 insertions(+)
>>> create mode 100644 Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt
>>> create mode 100644 drivers/phy/phy-bcm-ns2-usbdrd.c
>>>

\
 
 \ /
  Last update: 2017-06-12 01:43    [W:0.068 / U:0.456 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site