lkml.org 
[lkml]   [2017]   [Jun]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 1/2] dt-bindings: pwm-backlight: Add pwm-delay-us property
Hi Daniel, Pavel,

2017-06-28 15:30 GMT+02:00 Pavel Machek <pavel@ucw.cz>:
> On Wed 2017-06-28 13:16:31, Enric Balletbo i Serra wrote:
>> From: huang lin <hl@rock-chips.com>
>>
>> Add a pwm-delay-us property to specify the delay between setting an
>> initial (non-zero) PWM value and enabling the backlight, and also the
>> delay between disabling the backlight and setting PWM value to 0.
>
>
>
>> Signed-off-by: huang lin <hl@rock-chips.com>
>> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
>> ---
>> Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt | 4 ++++
>> 1 file changed, 4 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt b/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt
>> index 764db86..f75b08f 100644
>> --- a/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt
>> +++ b/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt
>> @@ -17,6 +17,9 @@ Optional properties:
>> "pwms" property (see PWM binding[0])
>> - enable-gpios: contains a single GPIO specifier for the GPIO which enables
>> and disables the backlight (see GPIO binding[1])
>> + - pwm-delay-us: delay between setting an initial (non-zero) PWM value and
>> + enabling the backlight, and also the delay between disabling
>> + the backlight and setting PWM value to 0.
>>
>
>> If is safe to assume power-on delay and power-off delay will be the same?
>>
>> I've only took a quick look but several backlight controllers support asymetric power-on/off sequences..

Daniel, right the ones I checked are symmetric but asymmetric timings
are possible I guess, so I think now that specify the two delays is
more accurate, maybe the binding should be something like this?

pwm-delay-us = <delay_before_on delay_after_off>;

> I understood it as "you set PWM and it takes a while for display to
> light up"
> but that's not correct. Changelog from second patch makes it
> clear. Please
> clarify it here, too.

Pavel, oh, your dude is interesting ...

That's the idea, the sequence is:
Power on, you set the PWM signal, wait a bit and set the LED_EN signal.
Power off, you clear the LED_EN signal, wait a bit and stop the PWM signal.

Note that the patch inverts the sequence, before this patch first you
set LED_EN signal and then the PWM signal

I assumed that the sequence was wrong but maybe I'm mistaken and there
are some panels that follow the original sequence. On the few panels I
checked the power on/off sequence is how I described above, i.e. see
[1] p. 17, the sequence is first PWM and then LED_EN. I'll take a look
at other panel datasheets, or if you know one, could you provide me
the datasheet?

Thanks,

[1] http://www.jxlcd.com/Upload/PicFiles/N116BGE-L41.pdf

>
> Pavel
> --
> (english) http://www.livejournal.com/~pavelmachek
> (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

\
 
 \ /
  Last update: 2017-06-28 16:16    [W:0.054 / U:0.552 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site