lkml.org 
[lkml]   [2017]   [Jun]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 1/3] ARM: dts: Bindings for Altera Quadspi Controller Version 2
From
Date
On 06/26/2017 06:13 PM, matthew.gerlach@linux.intel.com wrote:
> From: Matthew Gerlach <matthew.gerlach@linux.intel.com>
>
> Device Tree bindings for Version 2 of the Altera Quadspi Controller
> that can be optionally paired with a windowed bridge.
>
> Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
> ---
> .../devicetree/bindings/mtd/altera-quadspi-v2.txt | 37 ++++++++++++++++++++++
> 1 file changed, 37 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mtd/altera-quadspi-v2.txt
>
> diff --git a/Documentation/devicetree/bindings/mtd/altera-quadspi-v2.txt b/Documentation/devicetree/bindings/mtd/altera-quadspi-v2.txt
> new file mode 100644
> index 0000000..8ba63d7
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mtd/altera-quadspi-v2.txt
> @@ -0,0 +1,37 @@
> +* Altera Quad SPI Controller Version 2
> +
> +Required properties:
> +- compatible : Should be "altr,quadspi-v2".
> +- reg : Contains at least two entries, and possibly three entries, each of
> + which is a tuple consisting of a physical address and length.
> +- reg-names : Should contain the names "avl_csr" and "avl_mem" corresponding
> + to the control and status registers and qspi memory, respectively.
> +
> +
> +The Altera Quad SPI Controller Version 2 can be paired with a windowed bridge
> +in order to reduce the footprint of the memory interface. When a windowed
> +bridge is used, reads and writes of data must be 32 bits wide.
> +
> +Optional properties:
> +- reg-names : Should contain the name "avl_window", if the windowed bridge
> + is used. This name corresponds to the register space that
> + controls the window.
> +- window-size : The size of the window which must be an even power of 2.
> +- read-bit-reverse : A boolean indicating the data read from the flash should
> + be bit reversed on a byte by byte basis before being
> + delivered to the MTD layer.
> +- write-bit-reverse : A boolean indicating the data written to the flash should
> + be bit reversed on a byte by byte basis.

Is there ever a usecase where you need to set just one of these props ?
Also, they're altera specific, so altr, prefix should be added.

> +Example:
> +
> +qspi: spi@a0001000 {
> + compatible = "altr,quadspi-v2";
> + reg = <0xa0001000 0x40>, <0xb0000000 0x4000000>;
> + reg-names = "avl_csr", "avl_mem";
> +
> + flash@0 {
> + reg = <0>;
> + label = "FPGA Image";
> + };
> +};
>


--
Best regards,
Marek Vasut

\
 
 \ /
  Last update: 2017-06-27 12:20    [W:2.566 / U:0.016 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site