lkml.org 
[lkml]   [2017]   [Jun]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 0/5] g_NCR5380: PDMA fixes and cleanup
On Sun, 25 Jun 2017, Ondrej Zary wrote:
>
> It mostly works, but there are some problems:
>
> It's not reliable - we continue the data transfer after poll_politely2
> returns zero but we don't know if it returned because of host buffer
> being ready of because of an IRQ. So if a device disconnects during write,
> we continue to fill the buffer and only then find out that wait for
> 53c80 registers timed out. Then PDMA gets disabled:
> [ 3458.774251] sd 2:0:1:0: [sdb] tag#0 53c80 registers not accessible, device will be reset
> [ 3458.774251] sd 2:0:1:0: [sdb] tag#0 switching to slow handshake
>

Sorry about that. I messed up the Gated-IRQ-is-asserted case when I
changed the algorithm to avoid adding more polling loops.

> We can just reset and continue with a new PDMA transfer.

We should only reset the 53c400 logic when there is a real failure (like
no access to 53c80 registers). If a reset is needed to handle normal
target behaviour (like disconnection during a slow transfer) then we are
doing something wrong.

> Found no problems with reads. But when this happens during a write, we
> might have lost some data buffers that we need to transfer again. The
> chip's PDMA block counter does not seem to be very helpful here -
> testing shows that either one buffer is missing in the file or is
> duplicated.
>
> That's why my code had separate host buffer ready and IRQ checks. Host
> buffer first - if it's ready, transfer the data. If not, check for IRQ -
> if it was an error, rollback 2 buffers (the same if the host buffer is
> not ready in time).
>

In v3 of the patch series I've fixed the Gated IRQ logic so the transfer
loop will terminate early.

>
> There's also a performance regression on DTC436 - the sg_tablesize limit
> affects performance badly.
> Before:
> # hdparm -t --direct /dev/sdb
>
> /dev/sdb:
> Timing O_DIRECT disk reads: 4 MB in 3.21 seconds = 1.25 MB/sec
>
> Now:
> # hdparm -t --direct /dev/sdb
>
> /dev/sdb:
> Timing O_DIRECT disk reads: 4 MB in 4.89 seconds = 837.69 kB/sec
>

The lost throughput can perhaps be explained by extra kernel-mode CPU
overhead. Next time maybe check for that with "time hdparm". Anyway, since
you have a patch, we should try to avoid this regression.

> We should limit the transfer size instead:
> --- a/drivers/scsi/g_NCR5380.c
> +++ b/drivers/scsi/g_NCR5380.c
> @@ -45,7 +45,8 @@
> int c400_blk_cnt; \
> int c400_host_buf; \
> int io_width; \
> - int pdma_residual
> + int pdma_residual; \
> + int board;
>
> #define NCR5380_dma_xfer_len generic_NCR5380_dma_xfer_len
> #define NCR5380_dma_recv_setup generic_NCR5380_pread
> @@ -247,7 +248,6 @@ static int generic_NCR5380_init_one(struct scsi_host_template *tpnt,
> case BOARD_DTC3181E:
> ports = dtc_3181e_ports;
> magic = ncr_53c400a_magic;
> - tpnt->sg_tablesize = 1;
> break;
> }
>

I've dropped my "sg_tablesize = 1" patch from the v3 series.

> @@ -317,6 +317,7 @@ static int generic_NCR5380_init_one(struct scsi_host_template *tpnt,
> }
> hostdata = shost_priv(instance);
>
> + hostdata->board = board;
> hostdata->io = iomem;
> hostdata->region_size = region_size;
>

I've added the hostdata->board variable in v3. It looks like we are going
to need it one way or another.

> @@ -625,6 +626,9 @@ static int generic_NCR5380_dma_xfer_len(struct NCR5380_hostdata *hostdata,
> /* 53C400 datasheet: non-modulo-128-byte transfers should use PIO */
> if (transfersize % 128)
> transfersize = 0;
> + /* Limit transfers to 512B to prevent random write corruption on DTC */
> + if (hostdata->board == BOARD_DTC3181E && transfersize > 512)
> + transfersize = 512;
>
> return min(transfersize, DMA_MAX_SIZE);
> }
>
>
> No data corruption

How did you confirm that? What about a 1024 byte limit? 2048? 4096? Does
it make any difference?

Do you have any theories that might explain the need for a 512 B limit?

My theory about the "read overrun" issue doesn't seem applicable, given
that this is actually the CMOS version, which has different errata than
the NMOS version.

The need for udelay(4) on this board does suggest timing issues. What
happens if you add a udelay into the generic_NCR5380_pwrite() loop?

> and no performance regression:
> # hdparm -t --direct /dev/sdb
>

Well, I'd still expect some added CPU overhead. The driver is being handed
a 4096 byte transfer and is now splitting that up into eight separate
transfers. That means eight times as many DMA setup and completion calls
and presumably a similar increase in interrupts.

> /dev/sdb:
> Timing O_DIRECT disk reads: 4 MB in 3.25 seconds = 1.23 MB/sec
>
> As the data corruption affects only writes, we could keep transfersize
> unlimited for reads:
> + /* Limit write transfers to 512B to prevent random corruption on DTC */
> + if (hostdata->board == BOARD_DTC3181E &&
> + cmd->sc_data_direction == DMA_TO_DEVICE && transfersize > 512)
> + transfersize = 512;
>
> So we can get some performance gain at least for reads:
> # hdparm -t --direct /dev/sdb
>
> /dev/sdb:
> Timing O_DIRECT disk reads: 6 MB in 4.17 seconds = 1.44 MB/sec
>

Right. No need to penalize read performance by splitting up transfers.

Anyway, I'd really like to get some idea of the root cause before I sign
off on this particular approach.

--

\
 
 \ /
  Last update: 2017-06-26 09:36    [W:1.796 / U:0.020 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site