lkml.org 
[lkml]   [2017]   [Jun]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH NET V5 2/2] net: hns: Use phy_driver to setup Phy loopback
On Mon, Jun 26, 2017 at 10:10:39AM +0800, Lin Yun Sheng wrote:
> Use function set_loopback in phy_driver to setup phy loopback
> when doing ethtool self test.
>
> Signed-off-by: Lin Yun Sheng <linyunsheng@huawei.com>
> ---
> drivers/net/ethernet/hisilicon/hns/hnae.h | 1 +
> drivers/net/ethernet/hisilicon/hns/hns_ethtool.c | 92 +++++++-----------------
> 2 files changed, 26 insertions(+), 67 deletions(-)
>
> diff --git a/drivers/net/ethernet/hisilicon/hns/hnae.h b/drivers/net/ethernet/hisilicon/hns/hnae.h
> index 04211ac..7ba653a 100644
> --- a/drivers/net/ethernet/hisilicon/hns/hnae.h
> +++ b/drivers/net/ethernet/hisilicon/hns/hnae.h
> @@ -360,6 +360,7 @@ enum hnae_loop {
> MAC_INTERNALLOOP_MAC = 0,
> MAC_INTERNALLOOP_SERDES,
> MAC_INTERNALLOOP_PHY,
> + MAC_LOOP_PHY_NONE,
> MAC_LOOP_NONE,
> };
>
> diff --git a/drivers/net/ethernet/hisilicon/hns/hns_ethtool.c b/drivers/net/ethernet/hisilicon/hns/hns_ethtool.c
> index e95795b..10d82df 100644
> --- a/drivers/net/ethernet/hisilicon/hns/hns_ethtool.c
> +++ b/drivers/net/ethernet/hisilicon/hns/hns_ethtool.c
> @@ -259,67 +259,24 @@ static int hns_nic_set_link_ksettings(struct net_device *net_dev,
>
> static int hns_nic_config_phy_loopback(struct phy_device *phy_dev, u8 en)
> {
> -#define COPPER_CONTROL_REG 0
> -#define PHY_POWER_DOWN BIT(11)
> -#define PHY_LOOP_BACK BIT(14)
> - u16 val = 0;
> -
> - if (phy_dev->is_c45) /* c45 branch adding for XGE PHY */
> - return -ENOTSUPP;
> + int err;
>
> if (en) {
> - /* speed : 1000M */
> - phy_write(phy_dev, HNS_PHY_PAGE_REG, 2);
> - phy_write(phy_dev, 21, 0x1046);
> -
> - phy_write(phy_dev, HNS_PHY_PAGE_REG, 0);
> - /* Force Master */
> - phy_write(phy_dev, 9, 0x1F00);
> -
> - /* Soft-reset */
> - phy_write(phy_dev, 0, 0x9140);
> - /* If autoneg disabled,two soft-reset operations */
> - phy_write(phy_dev, 0, 0x9140);
> -
> - phy_write(phy_dev, HNS_PHY_PAGE_REG, 0xFA);
> -
> - /* Default is 0x0400 */
> - phy_write(phy_dev, 1, 0x418);
> -
> - /* Force 1000M Link, Default is 0x0200 */
> - phy_write(phy_dev, 7, 0x20C);
> -
> - /* Powerup Fiber */
> - phy_write(phy_dev, HNS_PHY_PAGE_REG, 1);
> - val = phy_read(phy_dev, COPPER_CONTROL_REG);
> - val &= ~PHY_POWER_DOWN;
> - phy_write(phy_dev, COPPER_CONTROL_REG, val);
> -
> - /* Enable Phy Loopback */
> - phy_write(phy_dev, HNS_PHY_PAGE_REG, 0);
> - val = phy_read(phy_dev, COPPER_CONTROL_REG);
> - val |= PHY_LOOP_BACK;
> - val &= ~PHY_POWER_DOWN;
> - phy_write(phy_dev, COPPER_CONTROL_REG, val);
> + err = phy_resume(phy_dev);

Maybe this was discussed with an earlier version of these patches. Why
are using phy_resume() and phy_suspend()?

> static int __lb_setup(struct net_device *ndev,
> @@ -332,10 +289,8 @@ static int __lb_setup(struct net_device *ndev,
>
> switch (loop) {
> case MAC_INTERNALLOOP_PHY:
> - if ((phy_dev) && (!phy_dev->is_c45)) {
> - ret = hns_nic_config_phy_loopback(phy_dev, 0x1);
> - ret |= h->dev->ops->set_loopback(h, loop, 0x1);
> - }
> + ret = hns_nic_config_phy_loopback(phy_dev, 0x1);
> + ret |= h->dev->ops->set_loopback(h, loop, 0x1);

Or'ing together two errno values does not make much sense:

> + if (loop == MAC_INTERNALLOOP_PHY)
> + ret = __lb_setup(ndev, MAC_LOOP_PHY_NONE);
> + else
> + ret = __lb_setup(ndev, MAC_LOOP_NONE);
> if (ret)
> netdev_err(ndev, "%s: __lb_setup return error(%d)!\n",
> __func__,

And it looks like you even print the OR'ed version here!

Andrew

\
 
 \ /
  Last update: 2017-06-26 15:44    [W:0.081 / U:0.056 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site