lkml.org 
[lkml]   [2017]   [Jun]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 1/8] dt-bindings: mfd: Add STM32 LPTimer binding
From
Date
On 06/20/2017 01:50 PM, Lee Jones wrote:
> On Fri, 16 Jun 2017, Fabrice Gasnier wrote:
>
>> Add documentation for STMicroelectronics STM32 Low Power Timer binding.
>>
>> Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
>> ---
>> .../devicetree/bindings/mfd/stm32-lptimer.txt | 51 ++++++++++++++++++++++
>> 1 file changed, 51 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/mfd/stm32-lptimer.txt
>>
>> diff --git a/Documentation/devicetree/bindings/mfd/stm32-lptimer.txt b/Documentation/devicetree/bindings/mfd/stm32-lptimer.txt
>> new file mode 100644
>> index 0000000..237b7d6
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/mfd/stm32-lptimer.txt
>> @@ -0,0 +1,51 @@
>> +STMicroelectronics STM32 Low Power Timer
>> +
>> +The STM32 Low Power Timer (LPTIM) is a 16-bit timer that provides several
>> +functionalities:
>
> "functions".

Hi Lee,

I'll fix it in v2.
>
>> +- PWM output (with programmable prescaler, configurable polarity)
>> +- Quadrature encoder, counter
>> +- Trigger source for STM32 ADC/DAC (LPTIM_OUT)
>> +
>> +Required properties:
>> +- compatible: Must be "st,stm32-lptimer".
>> +- reg: Offset and length of the device's register set.
>> +- clocks: Phandle to the clock used by the LP Timer module.
>> +- clock-names: Must be "int".
>
> These look better when padded:
>
> - compatible: Must be "st,stm32-lptimer".
> - reg: Offset and length of the device's register set.
> - clocks: Phandle to the clock used by the LP Timer module.
> - clock-names: Must be "int".
>
>> +- #address-cells = <1>;
>> +- #size-cells = <0>;
>
> Please use the same format as you did for the other properties.

I'll fix it in v2.

>
>> +Optional properties:
>> +- resets: Must contain the phandle to the reset controller.
>> +
>> +Optional subnodes:
>> +- pwm: See ../pwm/pwm-stm32-lp.txt
>> +- counter: See ../iio/timer/stm32-lptimer-cnt.txt
>> +- trigger: See ../iio/timer/stm32-lptimer-trigger.txt
>> +
>> +Example:
>> +
>> + lptimer1: lptimer@0x40002400 {
>
> Remove '0x'
nice shot :-)

>
>> + compatible = "st,stm32-lptimer";
>> + reg = <0x40002400 0x400>;
>> + clocks = <&timer_clk>;
>> + clock-names = "int";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + pwm {
>> + compatible = "st,stm32-pwm-lp";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&lppwm1_pins>;
>> + };
>> +
>> + trigger@0 {
>
> Why is this @0 and no reg properties are provided for the other 2
> nodes?

This is to select each LPTimer configuration (similar to stm32-timers).
All LPTimers that provide output as trigger for ADC and/or DAC are the
same, except for which hardware signals they're connected to, and send
to ADC and/or DAC.
"reg" is used as index for trigger table in trigger driver code (PATCH
6): it must be 0 for lptimer1 output, 1 for lptimer2 output or 2 for
lptimer3 output.
I should probably document it in stm32-lptimer-trigger dt-bindings ?

This is not needed for other two nodes.

Thanks for reviewing,
Best Regards,
Fabrice

>
>> + compatible = "st,stm32-lptimer-trigger";
>> + reg = <0>;
>> + };
>> +
>> + counter {
>> + compatible = "st,stm32-lptimer-counter";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&lptim1_in_pins>;
>> + };
>> + };
>

\
 
 \ /
  Last update: 2017-06-20 18:07    [W:0.573 / U:0.072 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site