lkml.org 
[lkml]   [2017]   [May]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH 0/6] tty: serial: lpuart: add imx7ulp support
Date
From: Dong Aisheng <aisheng.dong@nxp.com> Sent: Tuesday, May 09, 2017 3:51 PM
>To: linux-serial@vger.kernel.org
>Cc: linux-kernel@vger.kernel.org; linux-arm-kernel@lists.infradead.org;
>gregkh@linuxfoundation.org; jslaby@suse.com; Andy Duan
><fugang.duan@nxp.com>; stefan@agner.ch; Mingkai Hu
><mingkai.hu@nxp.com>; Y.B. Lu <yangbo.lu@nxp.com>; A.S. Dong
><aisheng.dong@nxp.com>
>Subject: [PATCH 0/6] tty: serial: lpuart: add imx7ulp support
>
>This patch series mainly intends to add imx7ulp support which is also using FSL
>lpuart.
>
>The lpuart in imx7ulp is basically the same as ls1021a. It's also
>32 bit width register, but unlike ls1021a, it's little endian.
>Besides that, imx7ulp lpuart has a minor different register layout from ls1021a
>that it has four extra registers (verid, param, global,
>pincfg) located at the beginning of register map, which are currently not used
>by the driver and less to be used later.
>
>Furthermore, this patch serial also add a new more accurate baud rate
>calculation method as MX7ULP can't divide a suitable baud rate with the
>default setting.
>
>Currently the new baud rate calculation is only enabled on MX7ULP.
>However, i guess the Layerscape may also be able to use it as there seems to
>be no difference in baud rate setting register after checking the Layerscape
>Reference Manual.
>
>As i don't have Layerscape boards, i can't test it, so i only enable it for MX7ULP
>by default to avoid a potential break.
>
>I copied LayerScape guys in this series and hope they can help test later.
>If it works on Layerscape as well, then they can switch to the new setting too
>and totally remove the old stuff.
>
>Dong Aisheng (6):
> tty: serial: lpuart: introduce lpuart_soc_data to represent SoC
> property
> tty: serial: lpuart: add little endian 32 bit register support
> dt-bindings: serial: fsl-lpuart: add i.MX7ULP support
> tty: serial: lpuart: add imx7ulp support
> tty: serial: lpuart: add earlycon support for imx7ulp
> tty: serial: lpuart: add a more accurate baud rate calculation method
>
> .../devicetree/bindings/serial/fsl-lpuart.txt | 2 +
> drivers/tty/serial/fsl_lpuart.c | 149 ++++++++++++++++++---
> 2 files changed, 136 insertions(+), 15 deletions(-)
>
>--
>2.7.4

The series looks fine.

Acked-by: Fugang Duan <fugang.duan@nxp.com>

\
 
 \ /
  Last update: 2017-05-10 21:18    [W:0.173 / U:8.340 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site