lkml.org 
[lkml]   [2017]   [May]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 4/5] mmc: sdhci-esdhc-imx: Allow all supported prescaler values
Date
On i.MX, SYSCTL.SDCLKFS may always be set to 0 in order to make the SD
clock frequency prescaler divide by 1 in SDR mode, even with the eSDHC.
The previous minimum prescaler value of 2 in SDR mode with the eSDHC was
a code remnant from PowerPC, which actually has this limitation on
earlier revisions.

In DDR mode, the prescaler can divide by up to 512.

The maximum SD clock frequency in High Speed mode is 50 MHz. On i.MX25,
this change makes it possible to get 48 MHz from the USB PLL
(240 MHz / 5 / 1) instead of only 40 MHz from the USB PLL
(240 MHz / 3 / 2) or 33.25 MHz from the AHB clock (133 MHz / 2 / 2).

Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
---
Changes v1 -> v2: none.
---
drivers/mmc/host/sdhci-esdhc-imx.c | 18 +++++++-----------
1 file changed, 7 insertions(+), 11 deletions(-)

diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
index a0b7d4c..e0d06d9 100644
--- a/drivers/mmc/host/sdhci-esdhc-imx.c
+++ b/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -674,7 +674,8 @@ static inline void esdhc_pltfm_set_clock(struct sdhci_host *host,
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
unsigned int host_clock = pltfm_host->clock;
- int pre_div = 2;
+ int ddr_pre_div = imx_data->is_ddr ? 2 : 1;
+ int pre_div = 1;
int div = 1;
u32 temp, val;

@@ -689,28 +690,23 @@ static inline void esdhc_pltfm_set_clock(struct sdhci_host *host,
return;
}

- if (esdhc_is_usdhc(imx_data) && !imx_data->is_ddr)
- pre_div = 1;
-
temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL);
temp &= ~(ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN
| ESDHC_CLOCK_MASK);
sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL);

- while (host_clock / pre_div / 16 > clock && pre_div < 256)
+ while (host_clock / (16 * pre_div * ddr_pre_div) > clock &&
+ pre_div < 256)
pre_div *= 2;

- while (host_clock / pre_div / div > clock && div < 16)
+ while (host_clock / (div * pre_div * ddr_pre_div) > clock && div < 16)
div++;

- host->mmc->actual_clock = host_clock / pre_div / div;
+ host->mmc->actual_clock = host_clock / (div * pre_div * ddr_pre_div);
dev_dbg(mmc_dev(host->mmc), "desired SD clock: %d, actual: %d\n",
clock, host->mmc->actual_clock);

- if (imx_data->is_ddr)
- pre_div >>= 2;
- else
- pre_div >>= 1;
+ pre_div >>= 1;
div--;

temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL);
--
2.7.4
\
 
 \ /
  Last update: 2017-05-29 15:57    [W:0.045 / U:1.000 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site