lkml.org 
[lkml]   [2017]   [May]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v5 12/17] dt-bindings: qca7000-spi: Rework binding
Date
In preparation for the QCA7000 UART binding rework the binding document.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
---
.../devicetree/bindings/net/qca-qca7000-spi.txt | 49 +++++++++++++---------
1 file changed, 29 insertions(+), 20 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/qca-qca7000-spi.txt b/Documentation/devicetree/bindings/net/qca-qca7000-spi.txt
index c74989c..a37f656 100644
--- a/Documentation/devicetree/bindings/net/qca-qca7000-spi.txt
+++ b/Documentation/devicetree/bindings/net/qca-qca7000-spi.txt
@@ -1,29 +1,38 @@
-* Qualcomm QCA7000 (Ethernet over SPI protocol)
+* Qualcomm QCA7000

-Note: The QCA7000 is useable as a SPI device. In this case it must be defined
-as a child of a SPI master in the device tree.
+The QCA7000 is a serial-to-powerline bridge with a host interface which could
+be configured either as SPI or UART slave. This configuration is done by
+the QCA7000 firmware.
+
+(a) Ethernet over SPI
+
+In order to use the QCA7000 as SPI device it must be defined as a child of a
+SPI master in the device tree.

Required properties:
-- compatible : Should be "qca,qca7000"
-- reg : Should specify the SPI chip select
-- interrupts : The first cell should specify the index of the source interrupt
- and the second cell should specify the trigger type as rising edge
-- spi-cpha : Must be set
-- spi-cpol: Must be set
+- compatible : Should be "qca,qca7000"
+- reg : Should specify the SPI chip select
+- interrupts : The first cell should specify the index of the source
+ interrupt and the second cell should specify the trigger
+ type as rising edge
+- spi-cpha : Must be set
+- spi-cpol : Must be set

Optional properties:
-- interrupt-parent : Specify the pHandle of the source interrupt
+- interrupt-parent : Specify the pHandle of the source interrupt
- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at.
- Numbers smaller than 1000000 or greater than 16000000 are invalid. Missing
- the property will set the SPI frequency to 8000000 Hertz.
-- local-mac-address: 6 bytes, MAC address
-- qca,legacy-mode : Set the SPI data transfer of the QCA7000 to legacy mode.
- In this mode the SPI master must toggle the chip select between each data
- word. In burst mode these gaps aren't necessary, which is faster.
- This setting depends on how the QCA7000 is setup via GPIO pin strapping.
- If the property is missing the driver defaults to burst mode.
-
-Example:
+ Numbers smaller than 1000000 or greater than 16000000
+ are invalid. Missing the property will set the SPI
+ frequency to 8000000 Hertz.
+- local-mac-address : see ./ethernet.txt
+- qca,legacy-mode : Set the SPI data transfer of the QCA7000 to legacy mode.
+ In this mode the SPI master must toggle the chip select
+ between each data word. In burst mode these gaps aren't
+ necessary, which is faster. This setting depends on how
+ the QCA7000 is setup via GPIO pin strapping. If the
+ property is missing the driver defaults to burst mode.
+
+SPI Example:

/* Freescale i.MX28 SPI master*/
ssp2: spi@80014000 {
--
2.1.4
\
 
 \ /
  Last update: 2017-05-10 21:21    [W:0.107 / U:12.312 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site