lkml.org 
[lkml]   [2017]   [Apr]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v6 13/23] dt-bindings: PCI: dra7xx: Add DT bindings for PCI dra7xx EP mode
Date
Add device tree binding documentation for PCI dra7xx EP mode.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
---
Documentation/devicetree/bindings/pci/ti-pci.txt | 37 +++++++++++++++++++-----
1 file changed, 30 insertions(+), 7 deletions(-)

diff --git a/Documentation/devicetree/bindings/pci/ti-pci.txt b/Documentation/devicetree/bindings/pci/ti-pci.txt
index 60e25161f351..60c3cccefabc 100644
--- a/Documentation/devicetree/bindings/pci/ti-pci.txt
+++ b/Documentation/devicetree/bindings/pci/ti-pci.txt
@@ -1,17 +1,22 @@
TI PCI Controllers

PCIe Designware Controller
- - compatible: Should be "ti,dra7-pcie""
- - reg : Two register ranges as listed in the reg-names property
- - reg-names : The first entry must be "ti-conf" for the TI specific registers
- The second entry must be "rc-dbics" for the designware pcie
- registers
- The third entry must be "config" for the PCIe configuration space
+ - compatible: Should be "ti,dra7-pcie" for RC
+ Should be "ti,dra7-pcie-ep" for EP
- phys : list of PHY specifiers (used by generic PHY framework)
- phy-names : must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the
number of PHYs as specified in *phys* property.
- ti,hwmods : Name of the hwmod associated to the pcie, "pcie<X>",
where <X> is the instance number of the pcie from the HW spec.
+ - num-lanes as specified in ../designware-pcie.txt
+
+HOST MODE
+=========
+ - reg : Two register ranges as listed in the reg-names property
+ - reg-names : The first entry must be "ti-conf" for the TI specific registers
+ The second entry must be "rc-dbics" for the DesignWare PCIe
+ registers
+ The third entry must be "config" for the PCIe configuration space
- interrupts : Two interrupt entries must be specified. The first one is for
main interrupt line and the second for MSI interrupt line.
- #address-cells,
@@ -19,13 +24,31 @@ PCIe Designware Controller
#interrupt-cells,
device_type,
ranges,
- num-lanes,
interrupt-map-mask,
interrupt-map : as specified in ../designware-pcie.txt

+DEVICE MODE
+===========
+ - reg : Four register ranges as listed in the reg-names property
+ - reg-names : "ti-conf" for the TI specific registers
+ "ep_dbics" for the standard configuration registers as
+ they are locally accessed within the DIF CS space
+ "ep_dbics2" for the standard configuration registers as
+ they are locally accessed within the DIF CS2 space
+ "addr_space" used to map remote RC address space
+ - interrupts : one interrupt entries must be specified for main interrupt.
+ - num-ib-windows : number of inbound address translation windows
+ - num-ob-windows : number of outbound address translation windows
+
Optional Property:
- gpios : Should be added if a gpio line is required to drive PERST# line

+NOTE: Two DT nodes may be added for each PCI controller; one for host
+mode and another for device mode. So in order for PCI to
+work in host mode, EP mode DT node should be disabled and in order to PCI to
+work in EP mode, host mode DT node should be disabled. Host mode and EP
+mode are mutually exclusive.
+
Example:
axi {
compatible = "simple-bus";
--
2.11.0
\
 
 \ /
  Last update: 2017-04-05 11:00    [W:0.164 / U:0.204 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site