lkml.org 
[lkml]   [2017]   [Mar]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 1/2] dt-bindings: Document the STM32 QSPI bindings
Date
From: Ludovic Barre <ludovic.barre@st.com>

This patch adds documentation of device tree bindings for the STM32
QSPI controller.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
.../devicetree/bindings/mtd/stm32-quadspi.txt | 45 ++++++++++++++++++++++
1 file changed, 45 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mtd/stm32-quadspi.txt

diff --git a/Documentation/devicetree/bindings/mtd/stm32-quadspi.txt b/Documentation/devicetree/bindings/mtd/stm32-quadspi.txt
new file mode 100644
index 0000000..95a8ebd
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/stm32-quadspi.txt
@@ -0,0 +1,45 @@
+* STMicroelectronics Quad Serial Peripheral Interface(QuadSPI)
+
+Required properties:
+- compatible: should be "st,stm32f469-qspi"
+- reg: contains the register location and length.
+ (optional) the memory mapping address and length
+- reg-names: list of the names corresponding to the previous register
+ Should contain "qspi" to register location
+ (optional) "qspi_mm" if read in memory map mode (improve read throughput)
+- interrupts: should contain the interrupt for the device
+- clocks: the phandle of the clock needed by the QSPI controller
+- A pinctrl must be defined to set pins in mode of operation for QSPI transfer
+
+Optional properties:
+- resets: must contain the phandle to the reset controller.
+
+A spi flash must be a child of the nor_flash node and could have some
+properties. Also see jedec,spi-nor.txt.
+
+Required properties:
+- reg: chip-Select number (QSPI controller may connect 2 nor flashes)
+- spi-max-frequency: max frequency of spi bus
+
+Optional property:
+- spi-rx-bus-width: the bus width (number of data wires)
+
+Example:
+
+qspi: qspi@a0001000 {
+ compatible = "st,stm32f469-qspi";
+ reg = <0xa0001000 0x1000>, <0x90000000 0x10000000>;
+ reg-names = "qspi", "qspi_mm";
+ interrupts = <91>;
+ resets = <&rcc STM32F4_AHB3_RESET(QSPI)>;
+ clocks = <&rcc 0 STM32F4_AHB3_CLOCK(QSPI)>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qspi0>;
+
+ flash@0 {
+ reg = <0>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <108000000>;
+ ...
+ };
+};
--
2.7.4
\
 
 \ /
  Last update: 2017-03-27 14:57    [W:0.155 / U:0.180 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site