lkml.org 
[lkml]   [2017]   [Feb]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 2/7] serial: exar: Fix initialization of EXAR registers for ports > 0
On Tue, Feb 7, 2017 at 6:09 PM, Jan Kiszka <jan.kiszka@siemens.com> wrote:
> So far, pci_xr17v35x_setup always initialized 8XMODE, FCTR & Co. for
> port 0 because it used the address of that port instead of moving the
> pointer according to the port number. Fix this and remove the unneeded
> temporary ioremap by moving default_setup up and reusing the membase it
> fills into the port structure.

FWIW:
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>

One minor question below.

>
> Fixes: 14faa8cce88e ("tty/8250 Add support for Commtech's Fastcom Async-335 and Fastcom Async-PCIe cards")
> Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
> ---
> drivers/tty/serial/8250/8250_exar.c | 19 ++++++++-----------
> 1 file changed, 8 insertions(+), 11 deletions(-)
>
> diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c
> index 58469d9..d3e3a7d 100644
> --- a/drivers/tty/serial/8250/8250_exar.c
> +++ b/drivers/tty/serial/8250/8250_exar.c
> @@ -157,27 +157,24 @@ pci_xr17v35x_setup(struct exar8250 *priv, struct pci_dev *pcidev,
> if (board->has_slave && idx >= 8)
> port->port.uartclk /= 2;
>
> - p = pci_ioremap_bar(pcidev, 0);
> - if (!p)
> - return -ENOMEM;
> + ret = default_setup(priv, pcidev, idx, offset, port);
> + if (ret)
> + return ret;
>
> - /* Setup Multipurpose Input/Output pins. */
> - if (idx == 0)
> - setup_gpio(p);
> + p = port->port.membase;
>
> writeb(0x00, p + UART_EXAR_8XMODE);
> writeb(UART_FCTR_EXAR_TRGD, p + UART_EXAR_FCTR);
> writeb(128, p + UART_EXAR_TXTRG);
> writeb(128, p + UART_EXAR_RXTRG);
> - iounmap(p);
>
> - ret = default_setup(priv, pcidev, idx, offset, port);
> - if (ret)
> - return ret;
> + if (idx == 0) {
> + /* Setup Multipurpose Input/Output pins. */
> + setup_gpio(p);
>
> - if (idx == 0)

> port->port.private_data =
> xr17v35x_register_gpio(pcidev);

Can we do this on one line?

> + }
>
> return 0;
> }
> --
> 2.1.4
>



--
With Best Regards,
Andy Shevchenko

\
 
 \ /
  Last update: 2017-02-07 23:51    [W:0.095 / U:0.116 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site