lkml.org 
[lkml]   [2017]   [Dec]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 2/7] dt-bindings: soc: mediatek: add bindings document for USB wakeup
Date
This adds bindings document for the SSUSB-SPM glue layer driver found
in MediaTek SoCs which is used to support usb remote wakeup.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
.../bindings/soc/mediatek/usb-wakeup.txt | 77 ++++++++++++++++++++++
1 file changed, 77 insertions(+)
create mode 100644 Documentation/devicetree/bindings/soc/mediatek/usb-wakeup.txt

diff --git a/Documentation/devicetree/bindings/soc/mediatek/usb-wakeup.txt b/Documentation/devicetree/bindings/soc/mediatek/usb-wakeup.txt
new file mode 100644
index 0000000..313d927
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/mediatek/usb-wakeup.txt
@@ -0,0 +1,77 @@
+MediaTek USB Wakeup binding
+-----------------------------
+
+The SSUSB-SPM glue layer is used to control some signals of USB
+wakeup, such as IP-SLEEP, LINE-STATE, IDDIG etc, which are mutually
+exclusive.
+
+Required properties (controller (parent) node):
+- compatible: Should be one of:
+ - "mediatek,<soc-model>-uwk","mediatek,usb-wk-v1"
+ soc-model is the name of SoC, supports one of:
+ - mt8173, mt8176
+ - "mediatek,<soc-model>-uwk","mediatek,usb-wk-v2"
+ soc-model is the name of SoC, supports one of:
+ - mt2712
+
+- mediatek,wkc: must contain a syscon phandle, such as pericfg controller
+- #address-cells : should be '1'
+- #size-cells : should be '1'
+
+Required nodes: a sub-node is required for each glue layer provided for
+ each SSUSB IP. Address range information including the usual 'reg'
+ property is used inside these nodes to describe the controller's
+ topology.
+
+Required properties (glue layer (child) node):
+- reg: address and length of the register set within the syscon which is
+ assigned to @mediatek,wkc.
+- #mediatek,uwk-cells: should be 1 (see the second example), cell after
+ glue layer phandle is wakeup type from:
+ - MTU_WK_IP_SLEEP
+ - MTU_WK_LINE_STATE
+ The wakeup types defined in
+ - include/dt-bindings/soc/mediatek,usb-wakeup.h
+
+
+Example:
+
+usb_wakeup: uwk@0 {
+ compatible = "mediatek,mt2712-uwk","mediatek,usb-wk-v2";
+ mediatek,wkc = <&pericfg>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ status = "okay";
+
+ usb_wk0: uwk@510 {
+ reg = <0x510 0x4>;
+ #mediatek,uwk-cells = <1>;
+ status = "okay";
+ };
+
+ usb_wk1: uwk@514 {
+ reg = <0x514 0x4>;
+ #mediatek,uwk-cells = <1>;
+ status = "okay";
+ };
+};
+
+
+Specifying wakeup control of devices
+---------------------------------
+
+Device nodes should specify the configuration required in their
+"mediatek,uwks" property, containing a phandle to the glue layer
+node and a wakeup type, because each USB controller has just one
+glue layer for wakeup, so only one phandle is supported;
+
+Example:
+
+#include <dt-bindings/soc/mediatek,usb-wakeup.h>
+
+usb_host1: xhci@112c0000 {
+ ...
+ mediatek,uwks = <&usb_wk2 MTU_WK_IP_SLEEP>;
+ ...
+};
+
--
1.9.1
\
 
 \ /
  Last update: 2017-12-09 09:49    [W:0.072 / U:0.988 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site