lkml.org 
[lkml]   [2017]   [Dec]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH net-next v3 4/4] net: fec: add phy_reset_after_clk_enable() support
Date
From: Richard Leitner <dev@g0hl1n.net> Sent: Tuesday, December 05, 2017 9:26 PM
>Some PHYs (for example the SMSC LAN8710/LAN8720) doesn't allow turning
>the refclk on and off again during operation (according to their datasheet).
>Nonetheless exactly this behaviour was introduced for power saving reasons
>by commit e8fcfcd5684a ("net: fec: optimize the clock management to save
>power").
>Therefore add support for the phy_reset_after_clk_enable function from
>phylib to mitigate this issue.
>
>Generally speaking this issue is only relevant if the ref clk for the PHY is
>generated by the SoC and therefore the PHY is configured to "REF_CLK In
>Mode". In our specific case (PCB) this problem does occur at about every 10th
>to 50th POR of an LAN8710 connected to an i.MX6SOLO SoC. The typical
>symptom of this problem is a "swinging" ethernet link.
>Similar issues were reported by users of the NXP forum:
> https://emea01.safelinks.protection.outlook.com/?url=https%3A%2F
>%2Fcommunity.nxp.com%2Fthread%2F389902&data=02%7C01%7Cfugang.du
>an%40nxp.com%7C7f9fee272fc44662c2a108d53be3d1ee%7C686ea1d3bc2b4c6
>fa92cd99c5c301635%7C0%7C0%7C636480772022331090&sdata=7RdUsoWVWu
>o1nM5zKwLt7%2F6U3dxgDJtBDGlQCUWC6IM%3D&reserved=0
> https://emea01.safelinks.protection.outlook.com/?url=https%3A%2F
>%2Fcommunity.nxp.com%2Fmessage%2F309354&data=02%7C01%7Cfugang.d
>uan%40nxp.com%7C7f9fee272fc44662c2a108d53be3d1ee%7C686ea1d3bc2b4
>c6fa92cd99c5c301635%7C0%7C0%7C636480772022331090&sdata=D56KilGWD3
>kLABxc0yOI%2B44Y%2FhLfrGtdAvupCEyvI%2BI%3D&reserved=0
>With this patch applied the issue didn't occur for at least a few hundret PORs
>of our board.
>
>Fixes: e8fcfcd5684a ("net: fec: optimize the clock management to save
>power")
>Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
>---
> drivers/net/ethernet/freescale/fec_main.c | 7 +++++++
> 1 file changed, 7 insertions(+)
>
>diff --git a/drivers/net/ethernet/freescale/fec_main.c
>b/drivers/net/ethernet/freescale/fec_main.c
>index 610573855213..8c3d0fb7db20 100644
>--- a/drivers/net/ethernet/freescale/fec_main.c
>+++ b/drivers/net/ethernet/freescale/fec_main.c
>@@ -1862,6 +1862,8 @@ static int fec_enet_clk_enable(struct net_device
>*ndev, bool enable)
> ret = clk_prepare_enable(fep->clk_ref);
> if (ret)
> goto failed_clk_ref;
>+
>+ phy_reset_after_clk_enable(ndev->phydev);
> } else {
> clk_disable_unprepare(fep->clk_ahb);
> clk_disable_unprepare(fep->clk_enet_out);
>@@ -2860,6 +2862,11 @@ fec_enet_open(struct net_device *ndev)
> if (ret)
> goto err_enet_mii_probe;
>
>+ /* reset phy if needed here, due to the fact this is the first time we
>+ * have the net_device to phy_driver link
>+ */
>+ phy_reset_after_clk_enable(ndev->phydev);
>+

The patch series look better.
But why does it need to reset phy here since phy already is hard reset after clock enable.


> if (fep->quirks & FEC_QUIRK_ERR006687)
> imx6q_cpuidle_fec_irqs_used();
>
>--
>2.11.0

\
 
 \ /
  Last update: 2017-12-06 02:51    [W:0.085 / U:0.284 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site