lkml.org 
[lkml]   [2017]   [Dec]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2] drivers:mtd:spi-nor:checkup FSR error bits
Date
For Micron spi nor device, when erase/program operation
fails, especially the failure results from intending to
modify protected space, spi-nor upper layers still get
the return which shows the operation succeeds. This is
because current spi_nor_fsr_ready() only uses FSR bit.7
(flag status register) to check device whether ready.
This patch fixs this issue by checking relevant error
bits in FSR.
The FSR is a powerful tool to investigate the staus of
device, checking information regarding what is actually
doing the memory and detecting possible error conditions.

Signed-off-by: beanhuo <beanhuo@micron.com>
---
v1 - v2:
- Changed some error comments based on Cyrille's reviews.

drivers/mtd/spi-nor/spi-nor.c | 18 ++++++++++++++++--
include/linux/mtd/spi-nor.h | 6 +++++-
2 files changed, 21 insertions(+), 3 deletions(-)

diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
index 19c00072..4423605 100644
--- a/drivers/mtd/spi-nor/spi-nor.c
+++ b/drivers/mtd/spi-nor/spi-nor.c
@@ -328,8 +328,22 @@ static inline int spi_nor_fsr_ready(struct spi_nor *nor)
int fsr = read_fsr(nor);
if (fsr < 0)
return fsr;
- else
- return fsr & FSR_READY;
+
+ if (fsr & (FSR_E_ERR | FSR_P_ERR)) {
+ if (fsr & FSR_E_ERR)
+ dev_err(nor->dev, "Erase operation failed.\n");
+ else
+ dev_err(nor->dev, "Program operation failed.\n");
+
+ if (fsr & FSR_PT_ERR)
+ dev_err(nor->dev,
+ "Attempted to modify a protected sector.\n");
+
+ nor->write_reg(nor, SPINOR_OP_CLFSR, NULL, 0);
+ return -EIO;
+ }
+
+ return fsr & FSR_READY;
}

static int spi_nor_ready(struct spi_nor *nor)
diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
index 1f0a7fc..da8e0d5 100644
--- a/include/linux/mtd/spi-nor.h
+++ b/include/linux/mtd/spi-nor.h
@@ -61,6 +61,7 @@
#define SPINOR_OP_RDSFDP 0x5a /* Read SFDP */
#define SPINOR_OP_RDCR 0x35 /* Read configuration register */
#define SPINOR_OP_RDFSR 0x70 /* Read flag status register */
+#define SPINOR_OP_CLFSR 0x50 /* Clear flag status register */

/* 4-byte address opcodes - used on Spansion and some Macronix flashes. */
#define SPINOR_OP_READ_4B 0x13 /* Read data bytes (low frequency) */
@@ -130,7 +131,10 @@
#define EVCR_QUAD_EN_MICRON BIT(7) /* Micron Quad I/O */

/* Flag Status Register bits */
-#define FSR_READY BIT(7)
+#define FSR_READY BIT(7) /* Device status, 0 = Busy, 1 = Ready */
+#define FSR_E_ERR BIT(5) /* Erase operation status */
+#define FSR_P_ERR BIT(4) /* Program operation status */
+#define FSR_PT_ERR BIT(1) /* Protection error bit */

/* Configuration Register bits. */
#define CR_QUAD_EN_SPAN BIT(1) /* Spansion Quad I/O */
--
2.7.4
\
 
 \ /
  Last update: 2017-12-04 13:36    [W:0.034 / U:6.416 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site