lkml.org 
[lkml]   [2017]   [Dec]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v3 14/16] phy: Add notify_speed callback
From
Date
Hi,

On Tuesday 12 December 2017 08:54 PM, Manu Gautam wrote:
> Hi,
>
>
> On 12/12/2017 5:13 PM, Kishon Vijay Abraham I wrote:
>> Hi,
>>
>> On Tuesday 21 November 2017 02:53 PM, Manu Gautam wrote:
>>> QCOM USB PHYs can monitor resume/remote-wakeup event in
>>> suspended state. However PHY driver must know current
>>> operational speed of PHY in order to set correct polarity of
>>> wakeup events for detection. E.g. QUSB2 PHY monitors DP/DM
>>> signals depending on speed is LS or FS/HS to detect resume.
>>> Similarly QMP USB3 PHY in SS mode should monitor RX
>>> terminations attach/detach and LFPS events depending on
>>> SSPHY is active or not.

Why not use a notification mechanism instead of adding new APIs in phy-core.
This will only bloat phy-core with APIs for a particular platform.

Thanks
Kishon
>>>
>>> Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
>>> ---
>>> drivers/phy/phy-core.c | 30 ++++++++++++++++++++++++++++++
>>> include/linux/phy/phy.h | 26 ++++++++++++++++++++++++++
>>> 2 files changed, 56 insertions(+)
>>>
>>> diff --git a/drivers/phy/phy-core.c b/drivers/phy/phy-core.c
>>> index b4964b0..03df2be 100644
>>> --- a/drivers/phy/phy-core.c
>>> +++ b/drivers/phy/phy-core.c
>>> @@ -387,6 +387,36 @@ int phy_calibrate(struct phy *phy)
>>> }
>>> EXPORT_SYMBOL_GPL(phy_calibrate);
>>>
>>> +int phy_notify_speed(struct phy *phy, enum phy_speed speed)
>>> +{
>>> + int ret;
>>> +
>>> + if (!phy || !phy->ops->notify_speed)
>>> + return 0;
>>> +
>>> + mutex_lock(&phy->mutex);
>>> + ret = phy->ops->notify_speed(phy, speed);
>>> + mutex_unlock(&phy->mutex);
>>> +
>>> + return ret;
>>> +}
>>> +EXPORT_SYMBOL_GPL(phy_notify_speed);
>>> +
>>> +enum phy_speed phy_get_speed(struct phy *phy)
>>> +{
>>> + enum phy_speed ret;
>>> +
>>> + if (!phy || !phy->ops->get_speed)
>>> + return PHY_SPEED_UNKNOWN;
>>> +
>>> + mutex_lock(&phy->mutex);
>>> + ret = phy->ops->get_speed(phy);
>>> + mutex_unlock(&phy->mutex);
>>> +
>>> + return ret;
>>> +}
>>> +EXPORT_SYMBOL_GPL(phy_get_speed);
>> So this is equivalent to set_speed (why notify?) and get_speed. set_speed will
>> most likely be invoked by USB driver? who will invoke get_speed?
>
> I picked notify_speed as set_speed sounds like driver is going to set/program
> speed related configuration in PHY. Where as the purpose of this function
> is to notify phy_driver of the connection speed of established link.
> USB glue drivers for Qualcomm platforms need to know USB PHYs' speed to
> set correct polarity of wakeup interrupt from hardware in low power state.
>
>
>> Thanks
>> Kishon
>

\
 
 \ /
  Last update: 2017-12-20 06:49    [W:2.194 / U:0.508 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site