lkml.org 
[lkml]   [2017]   [Dec]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 2/2] phy: ti-pipe3: configure usb3 phy to be used as pcie phy
Date
DRA72 uses USB3 PHY for the 2nd lane of PCIE. The configuration
required to make USB3 PHY used for the 2nd lane of PCIe is done
here.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
drivers/phy/ti/phy-ti-pipe3.c | 47 +++++++++++++++++++++++++++++++++++++------
1 file changed, 41 insertions(+), 6 deletions(-)

diff --git a/drivers/phy/ti/phy-ti-pipe3.c b/drivers/phy/ti/phy-ti-pipe3.c
index 68ce4a082b9b..d5a7cc435fb7 100644
--- a/drivers/phy/ti/phy-ti-pipe3.c
+++ b/drivers/phy/ti/phy-ti-pipe3.c
@@ -56,6 +56,12 @@

#define SATA_PLL_SOFT_RESET BIT(18)

+#define PHY_RX_ANA_PRGRAMMABILITY_REG 0xC
+#define MEM_EN_PLLBYP BIT(7)
+
+#define PHY_TX_TEST_CONFIG 0x2C
+#define MEM_ENTESTCLK BIT(31)
+
#define PIPE3_PHY_PWRCTL_CLK_CMD_MASK 0x003FC000
#define PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT 14

@@ -110,6 +116,10 @@
#define PLL_IDLE_TIME 100 /* in milliseconds */
#define PLL_LOCK_TIME 100 /* in milliseconds */

+#define PIPE3_PHY_DISABLE_SYNC_POWER BIT(4)
+
+#define CONFIGURE_AS_PCIE BIT(0)
+
struct pipe3_dpll_params {
u16 m;
u8 n;
@@ -141,6 +151,7 @@ struct ti_pipe3 {
unsigned int power_reg; /* power reg. index within syscon */
unsigned int pcie_pcs_reg; /* pcs reg. index in syscon */
bool sata_refclk_enabled;
+ u32 flags;
};

static struct pipe3_dpll_map dpll_map_usb[] = {
@@ -233,11 +244,22 @@ static int ti_pipe3_power_on(struct phy *x)
rate = rate / 1000000;
mask = OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_MASK |
OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_MASK;
- val = PIPE3_PHY_TX_RX_POWERON << PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT;
+ val = PIPE3_PHY_TX_RX_POWERON;
+ if (phy->flags & CONFIGURE_AS_PCIE)
+ val |= PIPE3_PHY_DISABLE_SYNC_POWER;
+ val <<= PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT;
val |= rate << OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_SHIFT;

ret = regmap_update_bits(phy->phy_power_syscon, phy->power_reg,
mask, val);
+
+ if (phy->flags & CONFIGURE_AS_PCIE) {
+ ret = regmap_update_bits(phy->phy_power_syscon, phy->power_reg,
+ mask, val);
+ if (ret < 0)
+ return ret;
+ }
+
return ret;
}

@@ -335,6 +357,19 @@ static int ti_pipe3_init(struct phy *x)
int ret = 0;

ti_pipe3_enable_clocks(phy);
+
+ if (phy->flags & CONFIGURE_AS_PCIE) {
+ val = ti_pipe3_readl(phy->phy_rx,
+ PHY_RX_ANA_PRGRAMMABILITY_REG);
+ val |= MEM_EN_PLLBYP;
+ ti_pipe3_writel(phy->phy_rx, PHY_RX_ANA_PRGRAMMABILITY_REG,
+ val);
+ val = ti_pipe3_readl(phy->phy_tx, PHY_TX_TEST_CONFIG);
+ val |= MEM_ENTESTCLK;
+ ti_pipe3_writel(phy->phy_tx, PHY_TX_TEST_CONFIG, val);
+ return 0;
+ }
+
/*
* Set pcie_pcs register to 0x96 for proper functioning of phy
* as recommended in AM572x TRM SPRUHZ6, section 18.5.2.2, table
@@ -395,7 +430,8 @@ static int ti_pipe3_exit(struct phy *x)
return 0;

/* PCIe doesn't have internal DPLL */
- if (!of_device_is_compatible(phy->dev->of_node, "ti,phy-pipe3-pcie")) {
+ if (!of_device_is_compatible(phy->dev->of_node, "ti,phy-pipe3-pcie") &&
+ !(phy->flags & CONFIGURE_AS_PCIE)) {
/* Put DPLL in IDLE mode */
val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION2);
val |= PLL_IDLE;
@@ -589,12 +625,8 @@ static int ti_pipe3_get_tx_rx_base(struct ti_pipe3 *phy)
{
struct resource *res;
struct device *dev = phy->dev;
- struct device_node *node = dev->of_node;
struct platform_device *pdev = to_platform_device(dev);

- if (!of_device_is_compatible(node, "ti,phy-pipe3-pcie"))
- return 0;
-
res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
"phy_rx");
phy->phy_rx = devm_ioremap_resource(dev, res);
@@ -666,6 +698,9 @@ static int ti_pipe3_probe(struct platform_device *pdev)
if (ret)
return ret;

+ if (of_property_read_bool(node, "ti,configure-as-pcie"))
+ phy->flags |= CONFIGURE_AS_PCIE;
+
platform_set_drvdata(pdev, phy);
pm_runtime_enable(dev);

--
2.11.0
\
 
 \ /
  Last update: 2017-12-19 10:47    [W:0.414 / U:0.000 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site