lkml.org 
[lkml]   [2017]   [Nov]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 1/2] ARM: dts: Add the support for display5 equipped with Mitsubishi (800x480) display
Hi Lucas,

> Am Freitag, den 17.11.2017, 15:13 +0100 schrieb Lukasz Majewski:
> > Hi Shawn,
> >
> > > On Fri, Nov 17, 2017 at 11:24:03AM +0100, Lukasz Majewski wrote:
> > > > This is the support for aa070mc01-ca1 Mitsubishi display.
> > > >
> > > > Signed-off-by: Lukasz Majewski <lukma@denx.de>
> > > > ---
> > > >  arch/arm/boot/dts/Makefile                         |  1 +
> > > >  .../imx6q-display5-mitsubishi-aa070-800x480.dts    | 51
> > > > ++++++++++++++++++++++ 2 files changed, 52 insertions(+)
> > > >  create mode 100644
> > > > arch/arm/boot/dts/imx6q-display5-mitsubishi-aa070-800x480.dts
> > > >
> > > > diff --git a/arch/arm/boot/dts/Makefile
> > > > b/arch/arm/boot/dts/Makefile
> > > > index d9d0c82e7d20..10b3ad078dea 100644
> > > > --- a/arch/arm/boot/dts/Makefile
> > > > +++ b/arch/arm/boot/dts/Makefile
> > > > @@ -407,6 +407,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> > > >   imx6q-cm-fx6.dtb \
> > > >   imx6q-cubox-i.dtb \
> > > >   imx6q-dfi-fs700-m60.dtb \
> > > > + imx6q-display5-mitsubishi-aa070-800x480.dtb \
> > > >   imx6q-display5-tianma-tm070-1280x768.dtb \
> > > >   imx6q-dmo-edmqmx6.dtb \
> > > >   imx6q-evi.dtb \  
> > >
> > > <snip>
> > >
> > > > +#include "imx6q-display5.dtsi"
> > > > +
> > > > +&panel {
> > > > + compatible = "mitsubishi,aa070mc01-ca1";
> > > > +};  
> > >
> > > How many DTB files do you want to add for this display5 board?  
> >
> > This is a single board, which can support panels which I've posted.
> >
> > Those dtbs I do pack to u-boot' FIT image and don't need to worry
> > that
> > some display is not working (after setting bootloader env variable).
> >
> > > It's
> > > obvious no fun to maintain a bunch of DTB files for all the panels
> > > this board can support.
> >
> > Please note that those files excessively use #include directive, and
> > there is not so much code added (the longest part is license and
> > comments).
> >
> > >  Let's stop right here.
> >
> > If I may ask - how shall I proceed? What would be your suggestion to
> > move on (dtb overlays) ?
>
> The solution we use for the ZII RDU1 and RDU2 boards is to have the
> bootloader patch in the correct panel compatible strings.

Do you mean adjusting the DTB accordingly in u-boot for each display -
change panel/compatible to new display name ?

> This is
> quite a bit simpler than using overlays and if you already have a
> environment variable for this it should be easy to do.
>
> > >
> > > Shawn
> > >
> > > > +
> > > > +&ldb {
> > > > + lvds0: lvds-channel@0 {
> > > > + fsl,data-mapping = "spwg";
> > > > + fsl,data-width = <24>;
> > > > + };
> > > > +};
>
> This isn't needed. The panel compatible implies the data mapping and
> bus width (at least if you properly filled in this information in the
> panel driver).
>
> Regards,
> Lucas



Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd@denx.de
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2017-11-17 17:21    [W:0.066 / U:1.200 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site