lkml.org 
[lkml]   [2017]   [Oct]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH v6 05/11] dt-bindings: net: dwmac-sun8i: update documentation about integrated PHY
On Thu, Sep 28, 2017 at 09:37:08AM +0200, Corentin Labbe wrote:
> On Wed, Sep 27, 2017 at 04:02:10PM +0200, Andrew Lunn wrote:
> > Hi Corentin
> >
> > > +Required properties for the mdio-mux node:
> > > + - compatible = "mdio-mux"
> >
> > This is too generic. Please add a more specific compatible for this
> > particular mux. You can keep "mdio-mux", since that is what the MDIO
> > subsystem will look for.
> >
>
> I will add allwinner,sun8i-h3-mdio-mux
>
> > > +Required properties of the integrated phy node:
> > > - clocks: a phandle to the reference clock for the EPHY
> > > - resets: a phandle to the reset control for the EPHY
> > > +- phy-is-integrated
> >
> > So the last thing you said is that the mux is not the problem
> > here. Something else is locking up. Did you discover what?
> >
> > I really would like phy-is-integrated to go away.
> >
>
> I have found the problem: by enabling ephy clk/reset the timeout does not occur anymore.
> So we could remove phy-is-integrated by:
> Moving internal phy clk/reset handling in mdio_mux_syscon_switch_fn()
> But this means:
> - getting internalphy node always by manually get internal_mdio/internal_phy (and not by the given phyhandle)
> - doing some unnecessary tasks (enable/scan/disable) when external_phy is needed
>
> Regards

Hello all

Below is the current patch, as you can read, it does not use anymore the phy-is-integrated property.
So now, the mdio-mux must always enable the internal mdio when switch_fn ask for it and so reset MAC and so need to enable ephy clk/reset.
But for this I need a reference to thoses clock and reset. (this is done in get_ephy_nodes)
The current version set those clock in mdio-mux node, and as you can see it is already ugly (lots of get next node),
if the clk/rst nodes were as it should be, in phy nodes, it will be more bad.

So, since the MAC have a dependency on thoses clk/rst nodes for doing reset(), I seek a proper way to get references on it.
OR do you agree that putting ephy clk/rst in emac is acceptable ?

thanks
regards

--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
@@ -17,6 +17,7 @@
#include <linux/clk.h>
#include <linux/io.h>
#include <linux/iopoll.h>
+#include <linux/mdio-mux.h>
#include <linux/mfd/syscon.h>
#include <linux/module.h>
#include <linux/of_device.h>
@@ -41,14 +42,14 @@
* This value is used for disabling properly EMAC
* and used as a good starting value in case of the
* boot process(uboot) leave some stuff.
- * @internal_phy: Does the MAC embed an internal PHY
+ * @soc_has_internal_phy: Does the MAC embed an internal PHY
* @support_mii: Does the MAC handle MII
* @support_rmii: Does the MAC handle RMII
* @support_rgmii: Does the MAC handle RGMII
*/
struct emac_variant {
u32 default_syscon_value;
- int internal_phy;
+ bool soc_has_internal_phy;
bool support_mii;
bool support_rmii;
bool support_rgmii;
@@ -61,7 +62,7 @@ struct emac_variant {
* @rst_ephy: reference to the optional EPHY reset for the internal PHY
* @variant: reference to the current board variant
* @regmap: regmap for using the syscon
- * @use_internal_phy: Does the current PHY choice imply using the internal PHY
+ * @internal_phy_powered: Does the internal PHY is enabled
*/
struct sunxi_priv_data {
struct clk *tx_clk;
@@ -70,12 +71,13 @@ struct sunxi_priv_data {
struct reset_control *rst_ephy;
const struct emac_variant *variant;
struct regmap *regmap;
- bool use_internal_phy;
+ bool internal_phy_powered;
+ void *mux_handle;
};

static const struct emac_variant emac_variant_h3 = {
.default_syscon_value = 0x58000,
- .internal_phy = PHY_INTERFACE_MODE_MII,
+ .soc_has_internal_phy = true,
.support_mii = true,
.support_rmii = true,
.support_rgmii = true
@@ -83,20 +85,20 @@ static const struct emac_variant emac_variant_h3 = {

static const struct emac_variant emac_variant_v3s = {
.default_syscon_value = 0x38000,
- .internal_phy = PHY_INTERFACE_MODE_MII,
+ .soc_has_internal_phy = true,
.support_mii = true
};

static const struct emac_variant emac_variant_a83t = {
.default_syscon_value = 0,
- .internal_phy = 0,
+ .soc_has_internal_phy = false,
.support_mii = true,
.support_rgmii = true
};

static const struct emac_variant emac_variant_a64 = {
.default_syscon_value = 0,
- .internal_phy = 0,
+ .soc_has_internal_phy = false,
.support_mii = true,
.support_rmii = true,
.support_rgmii = true
@@ -195,6 +197,9 @@ static const struct emac_variant emac_variant_a64 = {
#define H3_EPHY_LED_POL BIT(17) /* 1: active low, 0: active high */
#define H3_EPHY_SHUTDOWN BIT(16) /* 1: shutdown, 0: power up */
#define H3_EPHY_SELECT BIT(15) /* 1: internal PHY, 0: external PHY */
+#define H3_EPHY_MUX_MASK (H3_EPHY_SHUTDOWN | H3_EPHY_SELECT)
+#define DWMAC_SUN8I_MDIO_MUX_INTERNAL_ID 1
+#define DWMAC_SUN8I_MDIO_MUX_EXTERNAL_ID 2

/* H3/A64 specific bits */
#define SYSCON_RMII_EN BIT(13) /* 1: enable RMII (overrides EPIT) */
@@ -634,6 +639,164 @@ static int sun8i_dwmac_reset(struct stmmac_priv *priv)
return 0;
}

+static int get_ephy_nodes(struct stmmac_priv *priv)
+{
+ struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
+ struct device_node *mdio_mux;
+ struct device_node *mdio_internal;
+ int ret;
+
+ mdio_mux = of_get_child_by_name(priv->plat->mdio_node, "mdio-mux");
+ if (!mdio_mux) {
+ dev_err(priv->device, "Cannot get mdio-mux node\n");
+ return -ENODEV;
+ }
+
+ mdio_internal = of_find_compatible_node(mdio_mux, NULL,
+ "allwinner,sun8i-h3-mdio-internal");
+ if (!mdio_internal) {
+ dev_err(priv->device, "Cannot get internal_mdio node\n");
+ return -ENODEV;
+ }
+
+ /* insert here code to get child phynode */
+ gmac->ephy_clk = of_clk_get(mdio_internal, 0);
+ if (IS_ERR(gmac->ephy_clk)) {
+ ret = PTR_ERR(gmac->ephy_clk);
+ dev_err(priv->device, "Cannot get EPHY clock: %d\n", ret);
+ return -EINVAL;
+ }
+
+ /* Note that we cannot use devm_reset_control_get, since
+ * the reset is not in the device node.
+ */
+ gmac->rst_ephy = of_reset_control_get_exclusive(mdio_internal, NULL);
+ if (IS_ERR(gmac->rst_ephy)) {
+ ret = PTR_ERR(gmac->rst_ephy);
+ if (ret == -EPROBE_DEFER)
+ return ret;
+ dev_err(priv->device, "No EPHY reset control found %d\n", ret);
+ return -EINVAL;
+ }
+ return 0;
+}
+
+static int sun8i_dwmac_power_internal_phy(struct stmmac_priv *priv)
+{
+ struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
+ int ret;
+
+ if (gmac->internal_phy_powered) {
+ dev_warn(priv->device, "Internal PHY already powered\n");
+ return 0;
+ }
+
+ dev_info(priv->device, "Powering internal PHY\n");
+ ret = clk_prepare_enable(gmac->ephy_clk);
+ if (ret) {
+ dev_err(priv->device, "Cannot enable internal PHY\n");
+ return ret;
+ }
+
+ /* Make sure the EPHY is properly reseted, as U-Boot may leave
+ * it at deasserted state, and thus it may fail to reset EMAC.
+ */
+ reset_control_assert(gmac->rst_ephy);
+
+ ret = reset_control_deassert(gmac->rst_ephy);
+ if (ret) {
+ dev_err(priv->device, "Cannot deassert internal phy\n");
+ clk_disable_unprepare(gmac->ephy_clk);
+ return ret;
+ }
+
+ gmac->internal_phy_powered = true;
+
+ return 0;
+}
+
+static int sun8i_dwmac_unpower_internal_phy(struct sunxi_priv_data *gmac)
+{
+ if (!gmac->internal_phy_powered)
+ return 0;
+
+ clk_disable_unprepare(gmac->ephy_clk);
+ reset_control_assert(gmac->rst_ephy);
+ gmac->internal_phy_powered = false;
+ return 0;
+}
+
+/* MDIO multiplexing switch function
+ * This function is called by the mdio-mux layer when it thinks the mdio bus
+ * multiplexer needs to switch.
+ * 'current_child' is the current value of the mux register
+ * 'desired_child' is the value of the 'reg' property of the target child MDIO
+ * node.
+ * The first time this function is called, current_child == -1.
+ * If current_child == desired_child, then the mux is already set to the
+ * correct bus.
+ *
+ * Note that we do not use reg/mask like mdio-mux-mmioreg because we need to
+ * know easily which bus is used (reset must be done only for desired bus).
+ */
+static int mdio_mux_syscon_switch_fn(int current_child, int desired_child,
+ void *data)
+{
+ struct stmmac_priv *priv = data;
+ struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
+ u32 reg, val;
+ int ret = 0;
+ bool need_power_ephy = false;
+
+ if (current_child ^ desired_child) {
+ regmap_read(gmac->regmap, SYSCON_EMAC_REG, &reg);
+ switch (desired_child) {
+ case DWMAC_SUN8I_MDIO_MUX_INTERNAL_ID:
+ dev_info(priv->device, "Switch mux to internal PHY");
+ val = (reg & ~H3_EPHY_MUX_MASK) | H3_EPHY_SELECT;
+
+ need_power_ephy = true;
+ break;
+ case DWMAC_SUN8I_MDIO_MUX_EXTERNAL_ID:
+ dev_info(priv->device, "Switch mux to external PHY");
+ val = (reg & ~H3_EPHY_MUX_MASK) | H3_EPHY_SHUTDOWN;
+ need_power_ephy = false;
+ break;
+ default:
+ dev_err(priv->device, "Invalid child ID %x\n",
+ desired_child);
+ return -EINVAL;
+ }
+ regmap_write(gmac->regmap, SYSCON_EMAC_REG, val);
+ if (need_power_ephy) {
+ ret = sun8i_dwmac_power_internal_phy(priv);
+ if (ret)
+ return ret;
+ } else {
+ sun8i_dwmac_unpower_internal_phy(gmac);
+ }
+ /* After changing syscon value, the MAC need reset or it will
+ * use the last value (and so the last PHY set).
+ */
+ ret = sun8i_dwmac_reset(priv);
+ }
+ return ret;
+}
+
+static int sun8i_dwmac_register_mdio_mux(struct stmmac_priv *priv)
+{
+ int ret;
+ struct device_node *mdio_mux;
+ struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
+
+ mdio_mux = of_get_child_by_name(priv->plat->mdio_node, "mdio-mux");
+ if (!mdio_mux)
+ return -ENODEV;
+
+ ret = mdio_mux_init(priv->device, mdio_mux, mdio_mux_syscon_switch_fn,
+ &gmac->mux_handle, priv, priv->mii);
+ return ret;
+}
+
static int sun8i_dwmac_set_syscon(struct stmmac_priv *priv)
{
struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
@@ -648,35 +811,25 @@ static int sun8i_dwmac_set_syscon(struct stmmac_priv *priv)
"Current syscon value is not the default %x (expect %x)\n",
val, reg);

- if (gmac->variant->internal_phy) {
- if (!gmac->use_internal_phy) {
- /* switch to external PHY interface */
- reg &= ~H3_EPHY_SELECT;
- } else {
- reg |= H3_EPHY_SELECT;
- reg &= ~H3_EPHY_SHUTDOWN;
- dev_dbg(priv->device, "Select internal_phy %x\n", reg);
-
- if (of_property_read_bool(priv->plat->phy_node,
- "allwinner,leds-active-low"))
- reg |= H3_EPHY_LED_POL;
- else
- reg &= ~H3_EPHY_LED_POL;
-
- /* Force EPHY xtal frequency to 24MHz. */
- reg |= H3_EPHY_CLK_SEL;
-
- ret = of_mdio_parse_addr(priv->device,
- priv->plat->phy_node);
- if (ret < 0) {
- dev_err(priv->device, "Could not parse MDIO addr\n");
- return ret;
- }
- /* of_mdio_parse_addr returns a valid (0 ~ 31) PHY
- * address. No need to mask it again.
- */
- reg |= ret << H3_EPHY_ADDR_SHIFT;
+ if (gmac->variant->soc_has_internal_phy) {
+ if (of_property_read_bool(priv->plat->phy_node,
+ "allwinner,leds-active-low"))
+ reg |= H3_EPHY_LED_POL;
+ else
+ reg &= ~H3_EPHY_LED_POL;
+
+ /* Force EPHY xtal frequency to 24MHz. */
+ reg |= H3_EPHY_CLK_SEL;
+
+ ret = of_mdio_parse_addr(priv->device, priv->plat->phy_node);
+ if (ret < 0) {
+ dev_err(priv->device, "Could not parse MDIO addr\n");
+ return ret;
}
+ /* of_mdio_parse_addr returns a valid (0 ~ 31) PHY
+ * address. No need to mask it again.
+ */
+ reg |= 1 << H3_EPHY_ADDR_SHIFT;
}

if (!of_property_read_u32(node, "allwinner,tx-delay-ps", &val)) {
@@ -746,81 +899,21 @@ static void sun8i_dwmac_unset_syscon(struct sunxi_priv_data *gmac)
regmap_write(gmac->regmap, SYSCON_EMAC_REG, reg);
}

-static int sun8i_dwmac_power_internal_phy(struct stmmac_priv *priv)
+static void sun8i_dwmac_exit(struct platform_device *pdev, void *priv)
{
- struct sunxi_priv_data *gmac = priv->plat->bsp_priv;
- int ret;
-
- if (!gmac->use_internal_phy)
- return 0;
-
- ret = clk_prepare_enable(gmac->ephy_clk);
- if (ret) {
- dev_err(priv->device, "Cannot enable ephy\n");
- return ret;
- }
-
- /* Make sure the EPHY is properly reseted, as U-Boot may leave
- * it at deasserted state, and thus it may fail to reset EMAC.
- */
- reset_control_assert(gmac->rst_ephy);
+ struct sunxi_priv_data *gmac = priv;

- ret = reset_control_deassert(gmac->rst_ephy);
- if (ret) {
- dev_err(priv->device, "Cannot deassert ephy\n");
- clk_disable_unprepare(gmac->ephy_clk);
- return ret;
+ if (gmac->variant->soc_has_internal_phy) {
+ /* sun8i_dwmac_exit could be called with mdiomux uninit */
+ if (gmac->mux_handle)
+ mdio_mux_uninit(gmac->mux_handle);
+ if (gmac->internal_phy_powered)
+ sun8i_dwmac_unpower_internal_phy(gmac);
}

- return 0;
-}
-
-static int sun8i_dwmac_unpower_internal_phy(struct sunxi_priv_data *gmac)
-{
- if (!gmac->use_internal_phy)
- return 0;
-
- clk_disable_unprepare(gmac->ephy_clk);
- reset_control_assert(gmac->rst_ephy);
- return 0;
-}
-
-/* sun8i_power_phy() - Activate the PHY:
- * In case of error, no need to call sun8i_unpower_phy(),
- * it will be called anyway by sun8i_dwmac_exit()
- */
-static int sun8i_power_phy(struct stmmac_priv *priv)
-{
- int ret;
-
- ret = sun8i_dwmac_power_internal_phy(priv);
- if (ret)
- return ret;
-
- ret = sun8i_dwmac_set_syscon(priv);
- if (ret)
- return ret;
-
- /* After changing syscon value, the MAC need reset or it will use
- * the last value (and so the last PHY set.
- */
- ret = sun8i_dwmac_reset(priv);
- if (ret)
- return ret;
- return 0;
-}
-
-static void sun8i_unpower_phy(struct sunxi_priv_data *gmac)
-{
sun8i_dwmac_unset_syscon(gmac);
- sun8i_dwmac_unpower_internal_phy(gmac);
-}

-static void sun8i_dwmac_exit(struct platform_device *pdev, void *priv)
-{
- struct sunxi_priv_data *gmac = priv;
-
- sun8i_unpower_phy(gmac);
+ reset_control_put(gmac->rst_ephy);

clk_disable_unprepare(gmac->tx_clk);

@@ -849,7 +942,7 @@ static struct mac_device_info *sun8i_dwmac_setup(void *ppriv)
if (!mac)
return NULL;

- ret = sun8i_power_phy(priv);
+ ret = sun8i_dwmac_set_syscon(priv);
if (ret)
return NULL;

@@ -889,6 +982,8 @@ static int sun8i_dwmac_probe(struct platform_device *pdev)
struct sunxi_priv_data *gmac;
struct device *dev = &pdev->dev;
int ret;
+ struct stmmac_priv *priv;
+ struct net_device *ndev;

ret = stmmac_get_platform_resources(pdev, &stmmac_res);
if (ret)
@@ -932,29 +1027,6 @@ static int sun8i_dwmac_probe(struct platform_device *pdev)
}

plat_dat->interface = of_get_phy_mode(dev->of_node);
- if (plat_dat->interface == gmac->variant->internal_phy) {
- dev_info(&pdev->dev, "Will use internal PHY\n");
- gmac->use_internal_phy = true;
- gmac->ephy_clk = of_clk_get(plat_dat->phy_node, 0);
- if (IS_ERR(gmac->ephy_clk)) {
- ret = PTR_ERR(gmac->ephy_clk);
- dev_err(&pdev->dev, "Cannot get EPHY clock: %d\n", ret);
- return -EINVAL;
- }
-
- gmac->rst_ephy = of_reset_control_get(plat_dat->phy_node, NULL);
- if (IS_ERR(gmac->rst_ephy)) {
- ret = PTR_ERR(gmac->rst_ephy);
- if (ret == -EPROBE_DEFER)
- return ret;
- dev_err(&pdev->dev, "No EPHY reset control found %d\n",
- ret);
- return -EINVAL;
- }
- } else {
- dev_info(&pdev->dev, "Will use external PHY\n");
- gmac->use_internal_phy = false;
- }

/* platform data specifying hardware features and callbacks.
* hardware features were copied from Allwinner drivers.
@@ -973,9 +1045,34 @@ static int sun8i_dwmac_probe(struct platform_device *pdev)

ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
if (ret)
- sun8i_dwmac_exit(pdev, plat_dat->bsp_priv);
+ goto dwmac_exit;
+
+ ndev = dev_get_drvdata(&pdev->dev);
+ priv = netdev_priv(ndev);
+ /* The mux must be registered after parent MDIO
+ * so after stmmac_dvr_probe()
+ */
+ if (gmac->variant->soc_has_internal_phy) {
+ ret = get_ephy_nodes(priv);
+ if (ret)
+ return ret;
+ ret = sun8i_dwmac_register_mdio_mux(priv);
+ if (ret) {
+ dev_err(&pdev->dev, "Failed to register mux\n");
+ goto dwmac_mux;
+ }
+ } else {
+ ret = sun8i_dwmac_reset(priv);
+ if (ret)
+ goto dwmac_exit;
+ }

return ret;
+dwmac_mux:
+ sun8i_dwmac_unset_syscon(gmac);
+dwmac_exit:
+ sun8i_dwmac_exit(pdev, plat_dat->bsp_priv);
+return ret;
}

static const struct of_device_id sun8i_dwmac_match[] = {
--
2.13.6
\
 
 \ /
  Last update: 2017-10-08 20:34    [W:0.096 / U:14.156 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site