lkml.org 
[lkml]   [2017]   [Oct]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v3 12/12] ARM: dtsi: axp81x: set pinmux for GPIO0/1 when used as LDOs
On Tue, Oct 10, 2017 at 03:09:11AM +0000, Chen-Yu Tsai wrote:
> On Wed, Oct 4, 2017 at 3:35 PM, Quentin Schulz
> <quentin.schulz@free-electrons.com> wrote:
> > Hi Chen-Yu, Linus,
> >
> > On 03/10/2017 17:08, Chen-Yu Tsai wrote:
> >> On Tue, Oct 3, 2017 at 10:47 PM, Maxime Ripard
> >> <maxime.ripard@free-electrons.com> wrote:
> >>> Hi Linus,
> >>>
> >>> On Tue, Oct 03, 2017 at 09:27:17AM +0000, Linus Walleij wrote:
> >>>> On Mon, Oct 2, 2017 at 2:08 PM, Quentin Schulz
> >>>> <quentin.schulz@free-electrons.com> wrote:
> >>>>
> >>>>> On AXP813/818, GPIO0 and GPIO1 can be used as LDO as (respectively)
> >>>>> ldo_io0 and ldo_io1.
> >>>> (...)
> >>>>> + gpio0_ldo: gpio0_ldo {
> >>>>> + pins = "GPIO0";
> >>>>> + function = "ldo";
> >>>>> + };
> >>>> (...)
> >>>>> + pinctrl-names = "default";
> >>>>> + pinctrl-0 = <&gpio0_ldo>;
> >>>>> /* Disable by default to avoid conflicts with GPIO */
> >>>>> status = "disabled";
> >>>>
> >>>> So this is still by default disabled, but you make the default
> >>>> mode something called "ldo".
> >>>>
> >>>> And I think that is to be understood as a low-dropout regulator?
> >>>>
> >>>> So is the idea that this should be represented as a regulator
> >>>> in the end?
> >>>>
> >>>> Then I think the state name should not be "default" rather
> >>>> something like "regulator" and "default" should be the GPIO
> >>>> mode, as I guess something like that exists.
> >>>>
> >>>> Activating a regulator using pin control "default" mode is
> >>>> not very pretty. It would probably be unintuitive and end
> >>>> up wasting power because people will get confused about
> >>>> what is going on.
> >>>
> >>> That's not really it. The PMIC has pins that can be muxed either to
> >>> (regular) GPIOs, an ADC or to an LDO regulator.
> >>>
> >>> This is just muxing, the regulator will be enabled and disabled
> >>> separately through another register. If it wasn't the case, it would
> >>> indeed be very messy.
> >>
> >> No. Actually they are controlled in the same register, so it is
> >> very messy. The muxing options are:
> >>
> >> - 0: drive low
> >> - 1: drive high
> >> - 2: input with interrupt triggering
> >> - 3: LDO on
> >> - 4: LDO off
> >> - 5~7: floating (or ADC)
> >>
> >
> > Just to be a little more precise,
> > - 0: drive low
> > - 1: drive high
> > - 2: input with interrupt triggering
> > - 3: LDO on
> > - 4: LDO off
> > - 5~7: floating (or ADC)
> >
> > for AXP813, and
> > - 0: drive low
> > - 1: drive high
> > - 2: input with interrupt triggering
> > - 3: LDO on
> > - 4: ADC
> > - 5~7: floating
> >
> > for AXP209.
> >
> > So I think what you suggested Linus is not really relevant here as the
> > regulator framework will take care of disabling the regulator when
> > needed (for AXP813 via the ldo_off "muxing" selected by the regulator
> > framework).
>
> Linus is suggesting that we use (switching between) pinctrl states to
> control the regulator, as opposed to overriding the register value
> directly. That would be nice, as both subsystems would have the same
> idea of what's actually happening in the hardware.
>
> As Linus mentioned, having the LDO on or off as the default pinctrl state
> is not pretty. It also means as soon as the device is brought up, the
> regulator state gets overridden. That would not work well for regulators
> that have/want the "always-on" or "boot-on" properties.

What about not enforcing any muxing state when we want to mux to the
"ldo" function? We just leave it to whatever value it is, that way we
keep it under the regulator framework's control, and we don't disrupt
anything when the pin is requested.

Maxime

--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2017-10-11 14:01    [W:0.881 / U:0.108 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site