lkml.org 
[lkml]   [2017]   [Jan]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
SubjectRe: [PATCH v1] mtd: spi nor: modify the boot and flash type of FMC
From
Date
Hi,

Le 06/01/2017 à 10:12, linshunquan 00354166 a écrit :
> (1) The HiSilicon Flash Memory Controller(FMC) is a multi-functions
> device which supports SPI Nor flash controller, SPI nand Flash
> controller and parallel nand flash controller. So when we are prepare
> to operation SPI Nor, we should make sure the flash type is SPI Nor.
>
> (2) Make sure the boot type is Normal Type before initialize the SPI
> Nor controller.
>
> Signed-off-by: linshunquan 00354166 <linshunquan1@hisilicon.com>
> ---
> drivers/mtd/spi-nor/hisi-sfc.c | 30 ++++++++++++++++++++++++++++++
> 1 file changed, 30 insertions(+)
>
> diff --git a/drivers/mtd/spi-nor/hisi-sfc.c b/drivers/mtd/spi-nor/hisi-sfc.c
> index 20378b0..7855024 100644
> --- a/drivers/mtd/spi-nor/hisi-sfc.c
> +++ b/drivers/mtd/spi-nor/hisi-sfc.c
> @@ -32,6 +32,8 @@
> #define FMC_CFG_OP_MODE_MASK BIT_MASK(0)
> #define FMC_CFG_OP_MODE_BOOT 0
> #define FMC_CFG_OP_MODE_NORMAL 1
> +#define FMC_CFG_OP_MODE_SEL(mode) ((mode) & 0x1)
> +#define FMC_CFG_FLASH_SEL_SPI_NOR (0x0 << 1)
> #define FMC_CFG_FLASH_SEL(type) (((type) & 0x3) << 1)
> #define FMC_CFG_FLASH_SEL_MASK 0x6
> #define FMC_ECC_TYPE(type) (((type) & 0x7) << 5)
> @@ -141,10 +143,36 @@ static int get_if_type(enum read_mode flash_read)
> return if_type;
> }
>
> +static void spi_nor_switch_spi_type(struct hifmc_host *host)
> +{
> + unsigned int reg;
> +
> + reg = readl(host->regbase + FMC_CFG);
> + if ((reg & FMC_CFG_FLASH_SEL_MASK)
> + == FMC_CFG_FLASH_SEL_SPI_NOR)
> + return;
> +
> + /* if the flash type isn't spi nor, change it */
> + reg &= ~FMC_CFG_FLASH_SEL_MASK;
> + reg |= FMC_CFG_FLASH_SEL(0);
> + writel(reg, host->regbase + FMC_CFG);
> +}
> +

This is not consistent: we have to check the macro definitions to
understand that FMC_CFG_FLASH_SPI_NOR == FMC_CFG_FLASH_SEL(0)

In such a function, you should use the very same macro for both the test
and the update of reg; either FMC_CFG_FLASH_SEL_SPI_NOR or
FMC_CFG_FLASH_SEL(0). Please don't mix the use of those macros.

> static void hisi_spi_nor_init(struct hifmc_host *host)
> {
> u32 reg;
>
> + /* switch the flash type to spi nor */
> + spi_nor_switch_spi_type(host);
> +
> + /* set the boot mode to normal */
> + reg = readl(host->regbase + FMC_CFG);
> + if ((reg & FMC_CFG_OP_MODE_MASK) == FMC_CFG_OP_MODE_BOOT) {
> + reg |= FMC_CFG_OP_MODE_SEL(FMC_CFG_OP_MODE_NORMAL);

This is not consistent: you test FMC_CFG_OP_MODE_BOOT, hence without
FMC_CFG_OP_MODE_SEL() but you set
FMC_CFG_OP_MODE_SEL(FMC_CFG_OP_MODE_NORMAL), with FMC_CFG_OP_MODE_SEL().

Of course, looking at the macro definitions, it works as is but once again
we have to check the macro definitions to understand why sometime you use
FMC_CFG_OP_MODE_SEL() whereas other times you don't.

> + writel(reg, host->regbase + FMC_CFG);
> + }

spi_nor_switch_spi_type() already updates the FMC_CFG register in the very
same manner: read, test, modify, write. Hence you should write a more
generic function and update both bitfields at once.

static void hisi_spi_nor_update_reg(struct hifmc_host *host,
unsigned int reg_offset,
unsigned int value,
unsigned int mask)
{
unsigned int reg;

reg = readl(host->regbase + reg_offset);
if (((reg ^ value) & mask) == 0)
return;

reg = (reg & ~mask) | (value & mask);
writel(reg, host->regbase + reg_offset);
}

...

unsigned int value, mask;

/*
* switch the flash type to spi nor and set the boot mode to
* normal.
*/
value = FMC_CFG_OP_MODE_NORMAL | FMC_CFG_FLASH_SEL_SPI_NOR;
mask = FMC_CFG_OP_MODE_MASK | FMC_CFG_FLASH_SEL_MASK;
hisi_spi_nor_update_reg(host, FMC_CFG, value, mask);

> +
> + /* set timming */
> reg = TIMING_CFG_TCSH(CS_HOLD_TIME)
> | TIMING_CFG_TCSS(CS_SETUP_TIME)
> | TIMING_CFG_TSHSL(CS_DESELECT_TIME);
> @@ -167,6 +195,8 @@ static int hisi_spi_nor_prep(struct spi_nor *nor, enum spi_nor_ops ops)
> if (ret)
> goto out;
>
> + spi_nor_switch_spi_type(host);
> +
> return 0;
>
> out:
>

Best regards,

Cyrille

\
 
 \ /
  Last update: 2017-01-06 14:48    [W:0.051 / U:0.440 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site