lkml.org 
[lkml]   [2017]   [Jan]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v5 1/5] devicetree: mfd: Add binding for the TI LM3533
Date
From: Bjorn Andersson <bjorn.andersson@sonymobile.com>

Add the binding for the Texas Instruments LM3533 lighting power
solution.

Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---

Changes since v4:
- Acks from Jonathan, Lee and Rob

Changes since v3:
- Added compatible to sub-nodes, per Lee's requested to treat them as separate
pieces.

Documentation/devicetree/bindings/mfd/lm3533.txt | 205 +++++++++++++++++++++++
1 file changed, 205 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/lm3533.txt

diff --git a/Documentation/devicetree/bindings/mfd/lm3533.txt b/Documentation/devicetree/bindings/mfd/lm3533.txt
new file mode 100644
index 000000000000..909281096ba2
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/lm3533.txt
@@ -0,0 +1,205 @@
+Texas Instruments LM3533 binding
+
+This binding describes the Texas Instruments LM3533, a lighting power solution
+for smartphone handsets. The common properties are described directly in the
+node, while each individual component are described in an optional subnode.
+
+- compatible:
+ Usage: required
+ Value type: <stringlist>
+ Definition: must be:
+ "ti,lm3533"
+
+- reg:
+ Usage: required
+ Value type: <u32>
+ Definition: i2c address of the LM3533 chip
+
+- als-supply:
+ Usage: optional
+ Value type: <prop-encoded-array>
+ Definition: reference to regulator powering the V_als input; as
+ specified in "../regulator/regulator.txt"
+
+- hwen-gpios:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: reference to gpio pin connected to the HWEN input; as
+ specified in "../gpio/gpio.txt"
+
+- ti,boost-freq-hz:
+ Usage: required
+ Value type: <u32>
+ Definition: switch-frequency of the boost converter, must be either:
+ 500000 or 1000000
+
+- ti,boost-ovp-mv:
+ Usage: required
+ Value type: <u32>
+ Definition: over-voltage protection limit, in mV. Must be one of:
+ 16000, 24000, 32000 or 40000
+
+- #address-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: must be 1
+
+- #size-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: must be 0
+
+= ALS SUBNODE
+The ambient light sensor subnode carrying the light sensor related properties.
+
+- compatible:
+ Usage: required
+ Value type: <stringlist>
+ Definition: must be:
+ "ti,lm3533-als"
+
+- ti,als-resistance-ohm:
+ Usage: required (unless ti,pwm-mode is specified)
+ Value type: <u32>
+ Definition: specifies the resistor value (R_als), in Ohm. Valid values
+ ranges from 200000 to 1574 Ohm.
+
+- ti,pwm-mode:
+ Usage: optional
+ Value type: <empty>
+ Definition: specifies, if present, that the als should operate in PWM
+ mode - rather than analog mode
+
+= BACKLIGHT NODES
+Backlight subnodes carrying the backlight related properties.
+
+- compatible:
+ Usage: required
+ Value type: <stringlist>
+ Definition: must be:
+ "ti,lm3533-backlight"
+
+- reg:
+ Usage: required
+ Value type: <u32>
+ Definition: specifies which of the two backlights this node corresponds
+ to
+
+- default-brightness:
+ Usage: optional
+ Value type: <32>
+ Definition: specifies the default brightness for the backlight, in
+ units of brightness [0-255]
+
+- label:
+ Usage: required
+ Value type: <string>
+ Definition: specifies a name of this backlight
+
+- led-max-microamp:
+ Usage: required
+ Value type: <u32>
+ Definition: specifies the max current for this backlight, in uA, as
+ described in "../leds/common.txt"
+
+- ti,pwm-zones:
+ Usage: optional
+ Value type: <u32 list>
+ Definition: lists the ALS zones to be PWM controlled for this backlight,
+ the values in the list are in the range [0 - 4]
+
+= LED NODES
+LED subnodes carrying the LED related properties.
+
+- compatible:
+ Usage: required
+ Value type: <stringlist>
+ Definition: must be:
+ "ti,lm3533-led"
+
+- reg:
+ Usage: required
+ Value type: <u32>
+ Definition: specifies which of the four LEDs this node corresponds to
+
+- linux,default-trigger:
+ Usage: optional
+ Value type: <string>
+ Definition: specifies the default trigger for the LED, as described in
+ "../leds/common.txt"
+
+- label:
+ Usage: required
+ Value type: <string>
+ Definition: specifies a name of this LED, as described in
+ "../leds/common.txt"
+
+- led-max-microamp:
+ Usage: required
+ Value type: <u32>
+ Definition: specifies the max current for this LED, in uA, as described
+ in "../leds/common.txt"
+
+- ti,pwm-zones:
+ Usage: optional
+ Value type: <u32 list>
+ Definition: lists the ALS zones to be PWM controlled for this LED, the
+ values in the list are in the range [0 - 4]
+
+= EXAMPLE
+
+i2c@12460000 {
+ compatible = "qcom,i2c-qup-v1.1.1";
+ ...
+
+ lm3533@36 {
+ compatible = "ti,lm3533";
+ reg = <0x36>;
+
+ als-supply = <&pm8921_l11>;
+ hwen-gpios = <&pm8921_gpio 26 GPIO_ACTIVE_HIGH>;
+
+ ti,boost-freq-hz = <500000>;
+ ti,boost-ovp-mv = <24000>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ als {
+ compatible = "ti,lm3533-als";
+ ti,als-resistance-ohm = <200000>;
+ };
+
+ backlight@0 {
+ compatible = "ti,lm3533-backlight";
+ reg = <0>;
+ label = "backlight";
+
+ led-max-microamp = <20200>;
+ };
+
+ led@0 {
+ compatible = "ti,lm3533-led";
+ reg = <0>;
+ label = "red";
+
+ led-max-microamp = <5000>;
+ };
+
+ led@1 {
+ compatible = "ti,lm3533-led";
+ reg = <1>;
+ label = "green";
+
+ led-max-microamp = <5000>;
+ };
+
+ led@2 {
+ compatible = "ti,lm3533-led";
+ reg = <2>;
+ label = "blue";
+
+ led-max-microamp = <5000>;
+ };
+ };
+
--
2.11.0
\
 
 \ /
  Last update: 2017-01-04 20:52    [W:0.075 / U:1.052 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site