lkml.org 
[lkml]   [2017]   [Jan]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v8 09/12] dt-bindings: mux-adg792a: document devicetree bindings for ADG792A/G mux
From
Date
On 2017-01-27 20:50, Rob Herring wrote:
> On Wed, Jan 18, 2017 at 04:57:12PM +0100, Peter Rosin wrote:
>> Analog Devices ADG792A/G is a triple 4:1 mux.
>>
>> Acked-by: Jonathan Cameron <jic23@kernel.org>
>> Signed-off-by: Peter Rosin <peda@axentia.se>
>> ---
>> .../devicetree/bindings/mux/mux-adg792a.txt | 79 ++++++++++++++++++++++
>> 1 file changed, 79 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/mux/mux-adg792a.txt
>>
>> diff --git a/Documentation/devicetree/bindings/mux/mux-adg792a.txt b/Documentation/devicetree/bindings/mux/mux-adg792a.txt
>> new file mode 100644
>> index 000000000000..0b26dd11f070
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/mux/mux-adg792a.txt
>> @@ -0,0 +1,79 @@
>> +Bindings for Analog Devices ADG792A/G Triple 4:1 Multiplexers
>> +
>> +Required properties:
>> +- compatible : "adi,adg792a" or "adi,adg792g"
>> +- #mux-control-cells : <0> if parallel, or <1> if not.
>> +* Standard mux-controller bindings as decribed in mux-controller.txt
>> +
>> +Optional properties for ADG792G:
>> +- gpio-controller : if present, #gpio-cells below is required.
>> +- #gpio-cells : should be <2>
>> + - First cell is the GPO line number, i.e. 0 or 1
>> + - Second cell is used to specify active high (0)
>> + or active low (1)
>> +
>> +Optional properties:
>> +- adi,parallel : if present, the three muxes are bound together with a single
>> + mux controller, controlling all three muxes in parallel.
>
> Can't this be implied by #mux-control-cells == 0?

Right, good point! I'll drop adi,parallel.

>> +- adi,idle-state : if present, array of 2-tuples with mux controller number
>> + and state that mux controllers will have when idle. States 0 through 3
>> + correspond to signals A through D in the datasheet.
>> +- adi,idle-high-impedance : if present, array of mux controller numbers that
>> + should be in the disconnected high-impedance state when idle.
>
> Perhaps combine these 2 to a common idle-state with the index being the
> mux controller number and a value of -1 (or 4) being hi-Z.

At one point [1] I had a straight array for the mux controllers with state 4
being hi-Z and state 5 being the default "leave mux as-is on release", but
Jonathan didn't like magic numbers. Can you please read the follow-ups to the
referenced mail for some background, and then pick out the most suitable color
for me to paint with? :-)

[1] https://lkml.org/lkml/2016/11/30/110

>> +
>> +Mux controller states 0 through 3 correspond to signals A through D in the
>> +datasheet. If a mux controller is mentioned in neither adi,idle-state nor
>> +adi,idle-high-impedance it is left in its previously selected state when idle.
>> +
>> +Example:
>> +
>> + /*
>> + * Three independent mux controllers (of which one is used).
>> + * Mux 0 is disconnected when idle, mux 1 idles with signal C
>> + * and mux 2 idles with signal A.
>> + */
>> + &i2c0 {
>> + mux: adg792a@50 {
>
> mux-controller@50

Yep. Hmm, where have I seen that before? :-)

Cheers,
peda

>> + compatible = "adi,adg792a";
>> + reg = <0x50>;
>> + #mux-control-cells = <1>;
>> +
>> + adi,idle-high-impedance = <0>;
>> + adi,idle-state = <1 2>, <2 0>;
>> + };
>> + };
>> +
>> + adc-mux {
>> + compatible = "io-channel-mux";
>> + io-channels = <&adc 0>;
>> + io-channel-names = "parent";
>> +
>> + mux-controls = <&mux 1>;
>> +
>> + channels = "sync-1", "", "out";
>> + };
>> +
>> +
>> + /*
>> + * Three parallel muxes with one mux controller, useful e.g. if
>> + * the adc is differential, thus needing two signals to be muxed
>> + * simultaneously for correct operation.
>> + */
>> + &i2c0 {
>> + pmux: adg792a@50 {
>> + compatible = "adi,adg792a";
>> + reg = <0x50>;
>> + #mux-control-cells = <0>;
>> + adi,parallel;
>> + };
>> + };
>> +
>> + diff-adc-mux {
>> + compatible = "io-channel-mux";
>> + io-channels = <&adc 0>;
>> + io-channel-names = "parent";
>> +
>> + mux-controls = <&pmux>;
>> +
>> + channels = "sync-1", "", "out";
>> + };
>> --
>> 2.1.4
>>
>> --
>> To unsubscribe from this list: send the line "unsubscribe devicetree" in
>> the body of a message to majordomo@vger.kernel.org
>> More majordomo info at http://vger.kernel.org/majordomo-info.html

\
 
 \ /
  Last update: 2017-01-28 00:48    [W:0.089 / U:1.060 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site