lkml.org 
[lkml]   [2017]   [Jan]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    From
    Subject[PATCH v5 0/13] arm64: allwinner: a64: Enable MMC support
    Date
    Hi,

    Here is a new attempt at getting the MMC controllers running, following the
    work done by Andre.

    This has been tested on a board with one SDIO device (a Marvell WiFi chip)
    and a Kingston eMMC with 1.8V IOs.

    For SDIO, the HS DDR mode works just fine. That serie also enables the
    SDR104 mode to work on the devices that are capable of this.

    For the eMMC, HS200 with the voltage switch works. HS400 doesn't at the
    moment, but since it's significantly more complex, and at the same time
    Allwinner recommends to limit its frequency to 100MHz, this doesn't have
    any benefits. If there's any at some point, this can be added later.

    Let me know what you think,
    Maxime

    Changes from v4:
    - Added Florian Tested-by
    - Removed duplicate commit log

    Changes from v3:
    - Reordered the MMC nodes
    - Added the specification section the first commit log
    - Supported mmc->actual_rate
    - Clarified a bit what we (don't) know about DATA0

    Changes from v2:
    - Enabled SDR104, limited the frequency to 150MHz. 200MHz was too high.
    - Added more fixes to the gating and frequency rate change sequence
    - Added one more patch to mask DATA0 when updating the clock that was
    needed to get SDR104 to run
    - Added the patches to enable it on a few boards done by Andre
    - Amended the comments as suggested by Andre.
    - Added some tags

    Andre Przywara (4):
    arm64: allwinner: a64: Add MMC nodes
    arm64: allwinner: pine64: add MMC support
    arm64: allwinner: a64: add UART1 pin nodes
    arm64: allwinner: add BananaPi-M64 support

    Maxime Ripard (9):
    mmc: sunxi: Fix clock frequency change sequence
    mmc: sunxi: Gate the clock when rate is 0
    mmc: sunxi: Always set signal delay to 0 for A64
    mmc: sunxi: Enable the new timings for the A64 MMC controllers
    mmc: sunxi: Mask DATA0 when updating the clock
    mmc: sunxi: Add EMMC (MMC2) controller compatible
    mmc: sunxi: Add more debug informations
    arm64: allwinner: a64: Add MMC pinctrl nodes
    arm64: allwinner: a64: Increase the MMC max frequency

    arch/arm64/boot/dts/allwinner/Makefile | 1 +-
    arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 120 +++++++-
    arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts | 20 +-
    arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 77 ++++-
    drivers/mmc/host/sunxi-mmc.c | 114 ++++---
    5 files changed, 289 insertions(+), 43 deletions(-)
    create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts

    base-commit: c94f7962e97c2ba0a612656bc456d979f20cb382
    --
    git-series 0.8.11

    \
     
     \ /
      Last update: 2017-01-27 22:48    [W:5.215 / U:0.296 seconds]
    ©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site