lkml.org 
[lkml]   [2017]   [Jan]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v4 10/13] arm64: allwinner: a64: Increase the MMC max frequency
From
Date
Hi Maxime,

On 01/26/2017 10:06 AM, Maxime Ripard wrote:
> The eMMC controller seem to have a maximum frequency of 200MHz, while the
> regular MMC controllers are capped at 150MHz.
>
> Since older SoCs cannot go that high, we cannot change the default maximum
> frequency, but fortunately for us we have a property for that in the DT.
>
> This also has the side effect of allowing to use the MMC HS200 and SD
> SDR104 modes for the boards that support it (with either 1.2v or 1.8v IOs).
>
> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
>
> arm64: allwinner: a64: Limit MMC0 and MMC1 rates to 150MHz
>
> Trying to set the bus to 200MHz on MMC1 when doing SDIO is failing.
> Allwinner sets the maximum for this bus to 150MHz, so enforce that limit.
>
> This hasn't been tested with MMC0, but the documented limit is the same,
> and I expect the behaviour to be the same.
>
> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

I suspect that you are trying to increase your number of Signed-off-by tags by
using unfair means :) Otherwise the squashed commit message is probably worth
some cleaning.

Best,
Florian

> ---
> arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 3 +++
> 1 file changed, 3 insertions(+), 0 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> index 7b79c319ad3c..cb3e0cf2191a 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> @@ -130,6 +130,7 @@
> resets = <&ccu RST_BUS_MMC0>;
> reset-names = "ahb";
> interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
> + max-frequency = <150000000>;
> status = "disabled";
> #address-cells = <1>;
> #size-cells = <0>;
> @@ -143,6 +144,7 @@
> resets = <&ccu RST_BUS_MMC1>;
> reset-names = "ahb";
> interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
> + max-frequency = <150000000>;
> status = "disabled";
> #address-cells = <1>;
> #size-cells = <0>;
> @@ -156,6 +158,7 @@
> resets = <&ccu RST_BUS_MMC2>;
> reset-names = "ahb";
> interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
> + max-frequency = <200000000>;
> status = "disabled";
> #address-cells = <1>;
> #size-cells = <0>;
>

\
 
 \ /
  Last update: 2017-01-27 11:41    [W:0.079 / U:0.708 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site