lkml.org 
[lkml]   [2017]   [Jan]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 4/4] ARM: dts: sun8i: add OTG function to Lichee Pi Zero
On Thu, Jan 12, 2017 at 04:13:34AM +0800, Icenowy Zheng wrote:
>
>
> 12.01.2017, 04:08, "Bin Liu" <b-liu@ti.com>:
> > On Thu, Jan 12, 2017 at 03:55:33AM +0800, Icenowy Zheng wrote:
> >>  11.01.2017, 04:24, "Bin Liu" <b-liu@ti.com>:
> >>  > On Tue, Jan 03, 2017 at 11:25:34PM +0800, Icenowy Zheng wrote:
> >>  >>  Lichee Pi Zero features a USB OTG port.
> >>  >>
> >>  >>  Add support for it.
> >>  >>
> >>  >>  Note: in order to use the Host mode, the board must be powered via the
> >>  >>  +5V and GND pins.
> >>  >>
> >>  >>  Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
> >>  >>  ---
> >>  >>   arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dts | 10 ++++++++++
> >>  >>   1 file changed, 10 insertions(+)
> >>  >>
> >>  >>  diff --git a/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dts b/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dts
> >>  >>  index 0099affc6ce3..3d9168cbaeca 100644
> >>  >>  --- a/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dts
> >>  >>  +++ b/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dts
> >>  >>  @@ -71,3 +71,13 @@
> >>  >>           pinctrl-names = "default";
> >>  >>           status = "okay";
> >>  >>   };
> >>  >>  +
> >>  >>  +&usb_otg {
> >>  >>  + dr_mode = "otg";
> >>  >
> >>  > Why not set this default mode in dtsi instead?
> >>  >
> >>  > Regards,
> >>  > -Bin.
> >>
> >>  There's possibly boards which do not have OTG functions.
> >
> > That is board specific.
> >
> > You'd better to define the default dr_mode which the musb _controller_
> > supports in the dtsi, and then override it in a specific board dts if
> > necessary.
>
> Is there MUSB controllers which do not support a certain mode?

I am not aware of any. That is why I recommended to set "otg" in dtsi,
then override it in board dts if a port is specically designed to
host-only or device-only mode.

>
> (I remembered my omap3-n900 which do not work under OTG mode...)

I belive it is n900 board specific. omap3 itself doesn't have such
limitation, AFAIK.

Regards,
-Bin.

>
> >
> > Regards,
> > -Bin.
> >
> >>  Even the official CDR design of V3s uses the USB controller to
> >>  connect a UVC webcam to make the design a dual-cam design
> >>  (V3s itself has a CSI).
> >>
> >>  >
> >>  >>  + status = "okay";
> >>  >>  +};
> >>  >>  +
> >>  >>  +&usbphy {
> >>  >>  + usb0_id_det-gpio = <&pio 5 6 GPIO_ACTIVE_HIGH>;
> >>  >>  + status = "okay";
> >>  >>  +};
> >>  >>  --
> >>  >>  2.11.0

\
 
 \ /
  Last update: 2017-01-11 21:37    [W:0.061 / U:0.528 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site