lkml.org 
[lkml]   [2016]   [Sep]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 3/3] arm: dts: thermal: add thermal/auxadc node.
From
Date


On 07/09/16 11:47, Dawei Chien wrote:
> On Tue, 2016-09-06 at 11:28 +0800, Dawei Chien wrote:
>> Dear Rui,
>>
>> On Tue, 2016-09-06 at 08:30 +0800, Zhang Rui wrote:
>>> On 二, 2016-09-06 at 08:24 +0800, Zhang Rui wrote:
>>>> On 四, 2016-08-18 at 11:50 +0800, Dawei Chien wrote:
>>>>>
>>>>> This adds the thermal controller and auxadc nodes
>>>>> to the Mediatek MT2701 dtsi file.
>>>>>
>>>>> Signed-off-by: Dawei Chien <dawei.chien@mediatek.com>
>>>>> ---
>>>>> This patch depned on:
>>>>> https://patchwork.kernel.org/patch/9249589/
>>>>> https://patchwork.kernel.org/patch/9249589/
>>>> Hmm, does this mean that I should take all these three patches and
>>>> hold
>>>> the patches in next merge window until the above patch has been
>>>> merged?
>>>>
>> Yes, this patch is base on auxadc patchset.
>>
>>> Patch 3/3 can not be applied on top of upstream kernel, so I guess it
>>> still has some other dependencies.
>>> I think I can apply patch 1, 2 first. And patch 3/3 should be handled
>>> in the dt tree.
>>
>> Sorry, this patch is also need Mediatek's clock patchset what I miss to
>> add in dependency list, I would resend this dt tree once clock patch
>> merge, or resend this for right dependency on next version, thank you.
>
> Actually, since patch1/patch2 would be OK so far, I would just only
> resend patch3 after MTK clock pathcset ready, I prefer to merge
> patch1/patch2 if possible, thank you.
>

From my side that's ok.

Regards,
Matthias

>
>>> thanks,
>>> rui
>>>> thanks,
>>>> rui
>>>>>
>>>>> ---
>>>>> arch/arm/boot/dts/mt2701.dtsi | 44
>>>>> +++++++++++++++++++++++++++++++++++++++++
>>>>> 1 file changed, 44 insertions(+)
>>>>>
>>>>> diff --git a/arch/arm/boot/dts/mt2701.dtsi
>>>>> b/arch/arm/boot/dts/mt2701.dtsi
>>>>> index e9150a4..cee4724 100644
>>>>> --- a/arch/arm/boot/dts/mt2701.dtsi
>>>>> +++ b/arch/arm/boot/dts/mt2701.dtsi
>>>>> @@ -87,6 +87,36 @@
>>>>> clock-output-names = "rtc32k";
>>>>> };
>>>>>
>>>>> + thermal-zones {
>>>>> + cpu_thermal: cpu_thermal {
>>>>> + polling-delay-passive = <1000>; /*
>>>>> milliseconds */
>>>>> + polling-delay = <1000>; /* milliseconds */
>>>>> +
>>>>> + thermal-sensors = <&thermal 0>;
>>>>> + sustainable-power = <1000>;
>>>>> +
>>>>> + trips {
>>>>> + threshold: trip-point@0 {
>>>>> + temperature = <68000>;
>>>>> + hysteresis = <2000>;
>>>>> + type = "passive";
>>>>> + };
>>>>> +
>>>>> + target: trip-point@1 {
>>>>> + temperature = <85000>;
>>>>> + hysteresis = <2000>;
>>>>> + type = "passive";
>>>>> + };
>>>>> +
>>>>> + cpu_crit: cpu_crit@0 {
>>>>> + temperature = <115000>;
>>>>> + hysteresis = <2000>;
>>>>> + type = "critical";
>>>>> + };
>>>>> + };
>>>>> + };
>>>>> + };
>>>>> +
>>>>> timer {
>>>>> compatible = "arm,armv7-timer";
>>>>> interrupt-parent = <&gic>;
>>>>> @@ -222,4 +252,18 @@
>>>>> clock-names = "baud", "bus";
>>>>> status = "disabled";
>>>>> };
>>>>> +
>>>>> + thermal: thermal@1100b000 {
>>>>> + #thermal-sensor-cells = <0>;
>>>>> + compatible = "mediatek,mt2701-thermal";
>>>>> + reg = <0 0x1100b000 0 0x1000>;
>>>>> + interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_LOW>;
>>>>> + clocks = <&pericfg CLK_PERI_THERM>, <&pericfg
>>>>> CLK_PERI_AUXADC>;
>>>>> + clock-names = "therm", "auxadc";
>>>>> + resets = <&pericfg 0x10>;
>>>>> + reset-names = "therm";
>>>>> + mediatek,auxadc = <&auxadc>;
>>>>> + mediatek,apmixedsys = <&apmixedsys>;
>>>>> + };
>>>>> +
>>>>> };
>>>> --
>>>> To unsubscribe from this list: send the line "unsubscribe linux-pm"
>>>> in
>>>> the body of a message to majordomo@vger.kernel.org
>>>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>
>
>

\
 
 \ /
  Last update: 2016-09-17 09:59    [W:0.079 / U:0.216 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site