lkml.org 
[lkml]   [2016]   [Aug]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v5 3/6] drm/i915/skl: Update plane watermarks atomically during plane updates
On Tue, Aug 02, 2016 at 02:20:33PM -0700, Matt Roper wrote:
> On Tue, Aug 02, 2016 at 02:52:51PM -0400, Lyude wrote:
> > Thanks to Ville for suggesting this as a potential solution to pipe
> > underruns on Skylake.
> >
> > On Skylake all of the registers for configuring planes, including the
> > registers for configuring their watermarks, are double buffered. New
> > values written to them won't take effect until said registers are
> > "armed", which is done by writing to the PLANE_SURF (or in the case of
> > cursor planes, the CURBASE register) register.
> >
> > With this in mind, up until now we've been updating watermarks on skl
> > like this:
> >
> > non-modeset {
> > - calculate (during atomic check phase)
> > - finish_atomic_commit:
> > - intel_pre_plane_update:
> > - intel_update_watermarks()
> > - {vblank happens; new watermarks + old plane values => underrun }
> > - drm_atomic_helper_commit_planes_on_crtc:
> > - start vblank evasion
> > - write new plane registers
> > - end vblank evasion
> > }
> >
> > or
> >
> > modeset {
> > - calculate (during atomic check phase)
> > - finish_atomic_commit:
> > - crtc_enable:
> > - intel_update_watermarks()
> > - {vblank happens; new watermarks + old plane values => underrun }
> > - drm_atomic_helper_commit_planes_on_crtc:
> > - start vblank evasion
> > - write new plane registers
> > - end vblank evasion
> > }
> >
> > Now we update watermarks atomically like this:
> >
> > non-modeset {
> > - calculate (during atomic check phase)
> > - finish_atomic_commit:
> > - intel_pre_plane_update:
> > - intel_update_watermarks() (wm values aren't written yet)
> > - drm_atomic_helper_commit_planes_on_crtc:
> > - start vblank evasion
> > - write new plane registers
> > - write new wm values
> > - end vblank evasion
> > }
> >
> > modeset {
> > - calculate (during atomic check phase)
> > - finish_atomic_commit:
> > - crtc_enable:
> > - intel_update_watermarks() (actual wm values aren't written
> > yet)
> > - drm_atomic_helper_commit_planes_on_crtc:
> > - start vblank evasion
> > - write new plane registers
> > - write new wm values
> > - end vblank evasion
> > }
> >
> > So this patch moves all of the watermark writes into the right place;
> > inside of the vblank evasion where we update all of the registers for
> > each plane. While this patch doesn't fix everything, it does allow us to
> > update the watermark values in the way the hardware expects us to.
> >
> > Changes since original patch series:
> > - Remove mutex_lock/mutex_unlock since they don't do anything and we're
> > not touching global state
> > - Move skl_write_cursor_wm/skl_write_plane_wm functions into
> > intel_pm.c, make externally visible
> > - Add skl_write_plane_wm calls to skl_update_plane
> > - Fix conditional for for loop in skl_write_plane_wm (level < max_level
> > should be level <= max_level)
> > - Make diagram in commit more accurate to what's actually happening
> > - Add Fixes:
> >
> > Changes since v1:
> > - Use IS_GEN9() instead of IS_SKYLAKE() since these fixes apply to more
> > then just Skylake
> > - Update description to make it clear this patch doesn't fix everything
> > - Check if pipes were actually changed before writing watermarks
> >
> > Changes since v2:
> > - Write PIPE_WM_LINETIME during vblank evasion
> >
> > Changes since v3:
> > - Rebase against new SAGV patch changes
> >
> > Changes since v4:
> > - Add a parameter to choose what skl_wm_values struct to use when
> > writing new plane watermarks
> >
> > Fixes: 2d41c0b59afc ("drm/i915/skl: SKL Watermark Computation")
> > Signed-off-by: Lyude <cpaul@redhat.com>
> > Cc: stable@vger.kernel.org
> > Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
> > Cc: Daniel Vetter <daniel.vetter@intel.com>
> > Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
> > Cc: Hans de Goede <hdegoede@redhat.com>
> > Cc: Matt Roper <matthew.d.roper@intel.com>

I imagine we'll eventually probably want to create a new display vfunc
to handle platform-specific pipe-level stuff that needs to happen under
vblank evasion (like the scalers and linetime WM we have today) to keep
the code clean; maybe add a TODO comment to that effect?

Anyway, this looks good enough for now, so

Reviewed-by: Matt Roper <matthew.d.roper@intel.com>

> > ---
> > drivers/gpu/drm/i915/intel_display.c | 8 +++++
> > drivers/gpu/drm/i915/intel_drv.h | 5 ++++
> > drivers/gpu/drm/i915/intel_pm.c | 58 ++++++++++++++++++++++++++----------
> > drivers/gpu/drm/i915/intel_sprite.c | 6 ++++
> > 4 files changed, 61 insertions(+), 16 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
> > index 76ba79f..79d146c 100644
> > --- a/drivers/gpu/drm/i915/intel_display.c
> > +++ b/drivers/gpu/drm/i915/intel_display.c
> > @@ -2980,6 +2980,7 @@ static void skylake_update_primary_plane(struct drm_plane *plane,
> > struct intel_crtc *intel_crtc = to_intel_crtc(crtc_state->base.crtc);
> > struct drm_framebuffer *fb = plane_state->base.fb;
> > struct drm_i915_gem_object *obj = intel_fb_obj(fb);
> > + struct skl_wm_values *wm = &dev_priv->wm.skl_results;
> > int pipe = intel_crtc->pipe;
> > u32 plane_ctl, stride_div, stride;
> > u32 tile_height, plane_offset, plane_size;
> > @@ -3031,6 +3032,9 @@ static void skylake_update_primary_plane(struct drm_plane *plane,
> > intel_crtc->adjusted_x = x_offset;
> > intel_crtc->adjusted_y = y_offset;
> >
> > + if (wm->dirty_pipes & drm_crtc_mask(&intel_crtc->base))
> > + skl_write_plane_wm(intel_crtc, wm, 0);
> > +
> > I915_WRITE(PLANE_CTL(pipe, 0), plane_ctl);
> > I915_WRITE(PLANE_OFFSET(pipe, 0), plane_offset);
> > I915_WRITE(PLANE_SIZE(pipe, 0), plane_size);
> > @@ -10243,9 +10247,13 @@ static void i9xx_update_cursor(struct drm_crtc *crtc, u32 base,
> > struct drm_device *dev = crtc->dev;
> > struct drm_i915_private *dev_priv = to_i915(dev);
> > struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
> > + struct skl_wm_values *wm = &dev_priv->wm.skl_results;
> > int pipe = intel_crtc->pipe;
> > uint32_t cntl = 0;
> >
> > + if (IS_GEN9(dev_priv) && wm->dirty_pipes & drm_crtc_mask(crtc))
> > + skl_write_cursor_wm(intel_crtc, wm);
> > +
> > if (plane_state && plane_state->visible) {
> > cntl = MCURSOR_GAMMA_ENABLE;
> > switch (plane_state->base.crtc_w) {
> > diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
> > index 6b0532a..1b444d3 100644
> > --- a/drivers/gpu/drm/i915/intel_drv.h
> > +++ b/drivers/gpu/drm/i915/intel_drv.h
> > @@ -1711,6 +1711,11 @@ void skl_ddb_get_hw_state(struct drm_i915_private *dev_priv,
> > struct skl_ddb_allocation *ddb /* out */);
> > int skl_enable_sagv(struct drm_i915_private *dev_priv);
> > int skl_disable_sagv(struct drm_i915_private *dev_priv);
> > +void skl_write_cursor_wm(struct intel_crtc *intel_crtc,
> > + const struct skl_wm_values *wm);
> > +void skl_write_plane_wm(struct intel_crtc *intel_crtc,
> > + const struct skl_wm_values *wm,
> > + int plane);
> > uint32_t ilk_pipe_pixel_rate(const struct intel_crtc_state *pipe_config);
> > bool ilk_disable_lp_wm(struct drm_device *dev);
> > int sanitize_rc6_option(struct drm_i915_private *dev_priv, int enable_rc6);
> > diff --git a/drivers/gpu/drm/i915/intel_pm.c b/drivers/gpu/drm/i915/intel_pm.c
> > index 7fd299e..53adcbf 100644
> > --- a/drivers/gpu/drm/i915/intel_pm.c
> > +++ b/drivers/gpu/drm/i915/intel_pm.c
> > @@ -3798,6 +3798,47 @@ static void skl_ddb_entry_write(struct drm_i915_private *dev_priv,
> > I915_WRITE(reg, 0);
> > }
> >
> > +void skl_write_plane_wm(struct intel_crtc *intel_crtc,
> > + const struct skl_wm_values *wm,
> > + int plane)
> > +{
> > + struct drm_crtc *crtc = &intel_crtc->base;
> > + struct drm_device *dev = crtc->dev;
> > + struct drm_i915_private *dev_priv = to_i915(dev);
> > + int level, max_level = ilk_wm_max_level(dev);
> > + enum pipe pipe = intel_crtc->pipe;
> > +
> > + if (!(wm->dirty_pipes & drm_crtc_mask(crtc)))
> > + return;
> > +
> > + I915_WRITE(PIPE_WM_LINETIME(pipe), wm->wm_linetime[pipe]);
>
> I think I mentioned this on the previous version, but if we program this
> here then it only gets programmed when a plane is being updated. It's
> possible that we could have the linetime value change due to a scaler
> update or a modeset, but without corresponding plane updates (e.g.,
> maybe all planes are off). So we probably need to make sure this value
> gets written outside the plane updates (but still under vblank evasion).
>
> > +
> > + for (level = 0; level <= max_level; level++) {
> > + I915_WRITE(PLANE_WM(pipe, plane, level),
> > + wm->plane[pipe][plane][level]);
> > + }
> > + I915_WRITE(PLANE_WM_TRANS(pipe, plane), wm->plane_trans[pipe][plane]);
>
> I notice that you moved the DDB update into skl_write_cursor_wm() down
> below, but didn't move the plane DDB update in here. I realize you
> remedy that in patch #6 where you finally fix up the flushing order, but
> the inconsistency between how cursor vs !cursor planes are handled seems
> confusing. Can we either move the plane DDB update here in this patch
> (we don't flush properly yet, but we're really no worse off than we
> already are), or can we defer the move of the cursor DDB to patch 6 to
> keep them consistent?
>
>
> Matt
>
> > +}
> > +
> > +void skl_write_cursor_wm(struct intel_crtc *intel_crtc,
> > + const struct skl_wm_values *wm)
> > +{
> > + struct drm_crtc *crtc = &intel_crtc->base;
> > + struct drm_device *dev = crtc->dev;
> > + struct drm_i915_private *dev_priv = to_i915(dev);
> > + int level, max_level = ilk_wm_max_level(dev);
> > + enum pipe pipe = intel_crtc->pipe;
> > +
> > + for (level = 0; level <= max_level; level++) {
> > + I915_WRITE(CUR_WM(pipe, level),
> > + wm->plane[pipe][PLANE_CURSOR][level]);
> > + }
> > + I915_WRITE(CUR_WM_TRANS(pipe), wm->plane_trans[pipe][PLANE_CURSOR]);
> > +
> > + skl_ddb_entry_write(dev_priv, CUR_BUF_CFG(pipe),
> > + &wm->ddb.plane[pipe][PLANE_CURSOR]);
> > +}
> > +
> > static void skl_write_wm_values(struct drm_i915_private *dev_priv,
> > const struct skl_wm_values *new)
> > {
> > @@ -3805,7 +3846,7 @@ static void skl_write_wm_values(struct drm_i915_private *dev_priv,
> > struct intel_crtc *crtc;
> >
> > for_each_intel_crtc(dev, crtc) {
> > - int i, level, max_level = ilk_wm_max_level(dev);
> > + int i;
> > enum pipe pipe = crtc->pipe;
> >
> > if ((new->dirty_pipes & drm_crtc_mask(&crtc->base)) == 0)
> > @@ -3813,21 +3854,6 @@ static void skl_write_wm_values(struct drm_i915_private *dev_priv,
> > if (!crtc->active)
> > continue;
> >
> > - I915_WRITE(PIPE_WM_LINETIME(pipe), new->wm_linetime[pipe]);
> > -
> > - for (level = 0; level <= max_level; level++) {
> > - for (i = 0; i < intel_num_planes(crtc); i++)
> > - I915_WRITE(PLANE_WM(pipe, i, level),
> > - new->plane[pipe][i][level]);
> > - I915_WRITE(CUR_WM(pipe, level),
> > - new->plane[pipe][PLANE_CURSOR][level]);
> > - }
> > - for (i = 0; i < intel_num_planes(crtc); i++)
> > - I915_WRITE(PLANE_WM_TRANS(pipe, i),
> > - new->plane_trans[pipe][i]);
> > - I915_WRITE(CUR_WM_TRANS(pipe),
> > - new->plane_trans[pipe][PLANE_CURSOR]);
> > -
> > for (i = 0; i < intel_num_planes(crtc); i++) {
> > skl_ddb_entry_write(dev_priv,
> > PLANE_BUF_CFG(pipe, i),
> > diff --git a/drivers/gpu/drm/i915/intel_sprite.c b/drivers/gpu/drm/i915/intel_sprite.c
> > index 0de935a..55d173f 100644
> > --- a/drivers/gpu/drm/i915/intel_sprite.c
> > +++ b/drivers/gpu/drm/i915/intel_sprite.c
> > @@ -203,6 +203,9 @@ skl_update_plane(struct drm_plane *drm_plane,
> > struct intel_plane *intel_plane = to_intel_plane(drm_plane);
> > struct drm_framebuffer *fb = plane_state->base.fb;
> > struct drm_i915_gem_object *obj = intel_fb_obj(fb);
> > + struct skl_wm_values *wm = &dev_priv->wm.skl_results;
> > + struct drm_crtc *crtc = crtc_state->base.crtc;
> > + struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
> > const int pipe = intel_plane->pipe;
> > const int plane = intel_plane->plane + 1;
> > u32 plane_ctl, stride_div, stride;
> > @@ -238,6 +241,9 @@ skl_update_plane(struct drm_plane *drm_plane,
> > crtc_w--;
> > crtc_h--;
> >
> > + if (wm->dirty_pipes & drm_crtc_mask(crtc))
> > + skl_write_plane_wm(intel_crtc, wm, plane);
> > +
> > if (key->flags) {
> > I915_WRITE(PLANE_KEYVAL(pipe, plane), key->min_value);
> > I915_WRITE(PLANE_KEYMAX(pipe, plane), key->max_value);
> > --
> > 2.7.4
> >
>
> --
> Matt Roper
> Graphics Software Engineer
> IoTG Platform Enabling & Development
> Intel Corporation
> (916) 356-2795

--
Matt Roper
Graphics Software Engineer
IoTG Platform Enabling & Development
Intel Corporation
(916) 356-2795

\
 
 \ /
  Last update: 2016-08-03 23:41    [W:0.567 / U:0.060 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site