lkml.org 
[lkml]   [2016]   [Aug]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 7/8] ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
Date
The AXP806 PMIC is the secondary PMIC. It provides various supply
voltages for the SoC and other peripherals. The PMIC's interrupt
line is connected to NMI pin of the SoC.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
Changes since v1:

- Fixed up bldo* voltage constraints to match regulator voltage step.

---
arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 112 ++++++++++++++++++++++++++++
1 file changed, 112 insertions(+)

diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
index 910b29f0f0b5..439847acd41e 100644
--- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
+++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
@@ -260,6 +260,118 @@
};
};

+ axp806: pmic@745 {
+ compatible = "x-powers,axp806";
+ reg = <0x745>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ bldoin-supply = <&reg_dcdce>;
+
+ regulators {
+ reg_s_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+ };
+
+ aldo2 {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's aldo's
+ */
+ regulator-name = "s_aldo2";
+ };
+
+ aldo3 {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's aldo's
+ */
+ regulator-name = "s_aldo3";
+ };
+
+ reg_bldo1: bldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-name = "vcc18-efuse-adc-display-csi";
+ };
+
+ reg_bldo2: bldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-name =
+ "vdd18-drampll-vcc18-pll-cpvdd";
+ };
+
+ bldo3 {
+ /* unused */
+ };
+
+ reg_bldo4: bldo4 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vcc12-hsic";
+ };
+
+ reg_cldo1: cldo1 {
+ /*
+ * This was 3V in the original design, but
+ * 3.3V is the recommended supply voltage
+ * for the Ethernet PHY.
+ */
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-gmac-phy";
+ };
+
+ reg_cldo2: cldo2 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "afvcc-cam";
+ };
+
+ reg_cldo3: cldo3 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-io-wifi-codec-io2";
+ };
+
+ reg_dcdca: dcdca {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpub";
+ };
+
+ reg_dcdcd: dcdcd {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-vpu";
+ };
+
+ reg_dcdce: dcdce {
+ regulator-always-on;
+ regulator-min-microvolt = <2100000>;
+ regulator-max-microvolt = <2100000>;
+ regulator-name = "vcc-bldo-codec-ldoin";
+ };
+
+ sw {
+ /*
+ * unused, but use a different name to
+ * avoid name clash with axp809's sw
+ */
+ regulator-name = "s_sw";
+ };
+ };
+ };
+
ac100: codec@e89 {
compatible = "x-powers,ac100";
reg = <0xe89>;
--
2.9.3
\
 
 \ /
  Last update: 2016-09-17 09:57    [W:0.117 / U:1.024 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site