lkml.org 
[lkml]   [2016]   [Jul]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 2/3] thermal: Add Mediatek thermal driver for mt2701.
Date
This patch adds support for mt2701 chip to mtk_thermal.c,
and integrate both mt8173 and mt2701 on the same driver.
MT8173 has four banks and five sensors, and MT2701 has
only one bank and three sensors.

Signed-off-by: Dawei Chien <dawei.chien@mediatek.com>
---
drivers/thermal/mtk_thermal.c | 258 ++++++++++++++++++++++++++---------------
1 file changed, 165 insertions(+), 93 deletions(-)

diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c
index 262ab0a..860f2e2 100644
--- a/drivers/thermal/mtk_thermal.c
+++ b/drivers/thermal/mtk_thermal.c
@@ -2,6 +2,7 @@
* Copyright (c) 2015 MediaTek Inc.
* Author: Hanyi Wu <hanyi.wu@mediatek.com>
* Sascha Hauer <s.hauer@pengutronix.de>
+ * Dawei Chien <dawei.chien@mediatek.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
@@ -21,6 +22,7 @@
#include <linux/nvmem-consumer.h>
#include <linux/of.h>
#include <linux/of_address.h>
+#include <linux/of_device.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
#include <linux/io.h>
@@ -88,6 +90,7 @@
#define TEMP_ADCVALIDMASK_VALID_HIGH BIT(5)
#define TEMP_ADCVALIDMASK_VALID_POS(bit) (bit)

+/* MT8173 thermal sensors */
#define MT8173_TS1 0
#define MT8173_TS2 1
#define MT8173_TS3 2
@@ -97,35 +100,62 @@
/* AUXADC channel 11 is used for the temperature sensors */
#define MT8173_TEMP_AUXADC_CHANNEL 11

-/* The total number of temperature sensors in the MT8173 */
-#define MT8173_NUM_SENSORS 5
-
-/* The number of banks in the MT8173 */
-#define MT8173_NUM_ZONES 4
-
-/* The number of sensing points per bank */
-#define MT8173_NUM_SENSORS_PER_ZONE 4
-
/* Layout of the fuses providing the calibration data */
-#define MT8173_CALIB_BUF0_VALID BIT(0)
-#define MT8173_CALIB_BUF1_ADC_GE(x) (((x) >> 22) & 0x3ff)
-#define MT8173_CALIB_BUF0_VTS_TS1(x) (((x) >> 17) & 0x1ff)
-#define MT8173_CALIB_BUF0_VTS_TS2(x) (((x) >> 8) & 0x1ff)
-#define MT8173_CALIB_BUF1_VTS_TS3(x) (((x) >> 0) & 0x1ff)
-#define MT8173_CALIB_BUF2_VTS_TS4(x) (((x) >> 23) & 0x1ff)
-#define MT8173_CALIB_BUF2_VTS_TSABB(x) (((x) >> 14) & 0x1ff)
-#define MT8173_CALIB_BUF0_DEGC_CALI(x) (((x) >> 1) & 0x3f)
-#define MT8173_CALIB_BUF0_O_SLOPE(x) (((x) >> 26) & 0x3f)
+#define CALIB_BUF0_VALID BIT(0)
+#define CALIB_BUF1_ADC_GE(x) (((x) >> 22) & 0x3ff)
+#define CALIB_BUF0_VTS_TS1(x) (((x) >> 17) & 0x1ff)
+#define CALIB_BUF0_VTS_TS2(x) (((x) >> 8) & 0x1ff)
+#define CALIB_BUF1_VTS_TS3(x) (((x) >> 0) & 0x1ff)
+#define CALIB_BUF2_VTS_TS4(x) (((x) >> 23) & 0x1ff)
+#define CALIB_BUF2_VTS_TS5(x) (((x) >> 14) & 0x1ff)
+#define CALIB_BUF0_DEGC_CALI(x) (((x) >> 1) & 0x3f)
+#define CALIB_BUF0_O_SLOPE(x) (((x) >> 26) & 0x3f)
+
+#define NVMEM_TS1 0
+#define NVMEM_TS2 1
+#define NVMEM_TS3 2
+#define NVMEM_TS4 3
+#define NVMEM_TS5 4
+
+/* MT2701 thermal sensors */
+#define MT2701_TS1 0
+#define MT2701_TS2 1
+#define MT2701_TSABB 2
+
+/* AUXADC channel 11 is used for the temperature sensors */
+#define MT2701_TEMP_AUXADC_CHANNEL 11

#define THERMAL_NAME "mtk-thermal"

+/* Maximum support banks */
+#define MAX_NUM_BANK 5
+
struct mtk_thermal;

+struct thermal_bank_cfg {
+ unsigned int num_sensors;
+ unsigned int sensors[MAX_NUM_BANK];
+};
+
struct mtk_thermal_bank {
struct mtk_thermal *mt;
int id;
};

+struct mtk_thermal_sense_point {
+ int msr;
+ int adcpnp;
+};
+
+struct mtk_thermal_data {
+ struct thermal_bank_cfg bank_data[MAX_NUM_BANK];
+ struct mtk_thermal_sense_point sensing_points[MAX_NUM_BANK];
+ int sensor_mux_values[MAX_NUM_BANK];
+ s32 num_banks;
+ s32 num_sensors;
+ s32 auxadc_channel;
+};
+
struct mtk_thermal {
struct device *dev;
void __iomem *thermal_base;
@@ -133,27 +163,20 @@ struct mtk_thermal {
struct clk *clk_peri_therm;
struct clk *clk_auxadc;

- struct mtk_thermal_bank banks[MT8173_NUM_ZONES];
-
+ struct mtk_thermal_bank banks[MAX_NUM_BANK];
+ const struct mtk_thermal_data *conf;
/* lock: for getting and putting banks */
struct mutex lock;
+ struct thermal_zone_device *tzd;

/* Calibration values */
s32 adc_ge;
s32 degc_cali;
s32 o_slope;
- s32 vts[MT8173_NUM_SENSORS];
-
-};
-
-struct mtk_thermal_bank_cfg {
- unsigned int num_sensors;
- unsigned int sensors[MT8173_NUM_SENSORS_PER_ZONE];
+ s32 vts[MAX_NUM_BANK];
};

-static const int sensor_mux_values[MT8173_NUM_SENSORS] = { 0, 1, 2, 3, 16 };
-
-/*
+/**
* The MT8173 thermal controller has four banks. Each bank can read up to
* four temperature sensors simultaneously. The MT8173 has a total of 5
* temperature sensors. We use each bank to measure a certain area of the
@@ -166,42 +189,76 @@ static const int sensor_mux_values[MT8173_NUM_SENSORS] = { 0, 1, 2, 3, 16 };
* data, and this indeed needs the temperatures of the individual banks
* for making better decisions.
*/
-static const struct mtk_thermal_bank_cfg bank_data[] = {
- {
- .num_sensors = 2,
- .sensors = { MT8173_TS2, MT8173_TS3 },
- }, {
- .num_sensors = 2,
- .sensors = { MT8173_TS2, MT8173_TS4 },
- }, {
- .num_sensors = 3,
- .sensors = { MT8173_TS1, MT8173_TS2, MT8173_TSABB },
- }, {
- .num_sensors = 1,
- .sensors = { MT8173_TS2 },
+static const struct mtk_thermal_data mt8173_thermal_data = {
+ .auxadc_channel = MT8173_TEMP_AUXADC_CHANNEL,
+ .num_banks = 4,
+ .num_sensors = 5,
+ .bank_data = {
+ {
+ .num_sensors = 2,
+ .sensors = { MT8173_TS2, MT8173_TS3 },
+ }, {
+ .num_sensors = 2,
+ .sensors = { MT8173_TS2, MT8173_TS4 },
+ }, {
+ .num_sensors = 3,
+ .sensors = { MT8173_TS1, MT8173_TS2, MT8173_TSABB },
+ }, {
+ .num_sensors = 1,
+ .sensors = { MT8173_TS2 },
+ },
},
+ .sensing_points = {
+ {
+ .msr = TEMP_MSR0,
+ .adcpnp = TEMP_ADCPNP0,
+ }, {
+ .msr = TEMP_MSR1,
+ .adcpnp = TEMP_ADCPNP1,
+ }, {
+ .msr = TEMP_MSR2,
+ .adcpnp = TEMP_ADCPNP2,
+ }, {
+ .msr = TEMP_MSR3,
+ .adcpnp = TEMP_ADCPNP3,
+ },
+ },
+ .sensor_mux_values = { 0, 1, 2, 3, 16 },
};

-struct mtk_thermal_sense_point {
- int msr;
- int adcpnp;
-};
-
-static const struct mtk_thermal_sense_point
- sensing_points[MT8173_NUM_SENSORS_PER_ZONE] = {
- {
- .msr = TEMP_MSR0,
- .adcpnp = TEMP_ADCPNP0,
- }, {
- .msr = TEMP_MSR1,
- .adcpnp = TEMP_ADCPNP1,
- }, {
- .msr = TEMP_MSR2,
- .adcpnp = TEMP_ADCPNP2,
- }, {
- .msr = TEMP_MSR3,
- .adcpnp = TEMP_ADCPNP3,
+/**
+ * The MT2701 thermal controller has one bank, which can read up to
+ * three temperature sensors simultaneously. The MT2701 has a total of 3
+ * temperature sensors.
+ *
+ * The thermal core only gets the maximum temperature of this one bank,
+ * so the bank concept wouldn't be necessary here. However, the SVS (Smart
+ * Voltage Scaling) unit makes its decisions based on the same bank
+ * data.
+ */
+static const struct mtk_thermal_data mt2701_thermal_data = {
+ .auxadc_channel = MT2701_TEMP_AUXADC_CHANNEL,
+ .num_banks = 1,
+ .num_sensors = 3,
+ .bank_data = {
+ {
+ .num_sensors = 3,
+ .sensors = { MT2701_TS1, MT2701_TS2, MT2701_TSABB },
+ },
},
+ .sensing_points = {
+ {
+ .msr = TEMP_MSR0,
+ .adcpnp = TEMP_ADCPNP0,
+ }, {
+ .msr = TEMP_MSR1,
+ .adcpnp = TEMP_ADCPNP1,
+ }, {
+ .msr = TEMP_MSR2,
+ .adcpnp = TEMP_ADCPNP2,
+ },
+ },
+ .sensor_mux_values = { 0, 1, 16},
};

/**
@@ -270,13 +327,15 @@ static void mtk_thermal_put_bank(struct mtk_thermal_bank *bank)
static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank)
{
struct mtk_thermal *mt = bank->mt;
+ const struct mtk_thermal_data *conf = mt->conf;
int i, temp = INT_MIN, max = INT_MIN;
u32 raw;

- for (i = 0; i < bank_data[bank->id].num_sensors; i++) {
- raw = readl(mt->thermal_base + sensing_points[i].msr);
+ for (i = 0; i < conf->bank_data[bank->id].num_sensors; i++) {
+ raw = readl(mt->thermal_base + conf->sensing_points[i].msr);

- temp = raw_to_mcelsius(mt, bank_data[bank->id].sensors[i], raw);
+ temp = raw_to_mcelsius(mt, conf->bank_data[bank->id].sensors[i],
+ raw);

/*
* The first read of a sensor often contains very high bogus
@@ -299,7 +358,7 @@ static int mtk_read_temp(void *data, int *temperature)
int i;
int tempmax = INT_MIN;

- for (i = 0; i < MT8173_NUM_ZONES; i++) {
+ for (i = 0; i < mt->conf->num_banks; i++) {
struct mtk_thermal_bank *bank = &mt->banks[i];

mtk_thermal_get_bank(bank);
@@ -322,7 +381,7 @@ static void mtk_thermal_init_bank(struct mtk_thermal *mt, int num,
u32 apmixed_phys_base, u32 auxadc_phys_base)
{
struct mtk_thermal_bank *bank = &mt->banks[num];
- const struct mtk_thermal_bank_cfg *cfg = &bank_data[num];
+ const struct mtk_thermal_data *conf = mt->conf;
int i;

bank->id = num;
@@ -368,7 +427,7 @@ static void mtk_thermal_init_bank(struct mtk_thermal *mt, int num,
* this value will be stored to TEMP_PNPMUXADDR (TEMP_SPARE0)
* automatically by hw
*/
- writel(BIT(MT8173_TEMP_AUXADC_CHANNEL), mt->thermal_base + TEMP_ADCMUX);
+ writel(BIT(conf->auxadc_channel), mt->thermal_base + TEMP_ADCMUX);

/* AHB address for auxadc mux selection */
writel(auxadc_phys_base + AUXADC_CON1_CLR_V,
@@ -379,18 +438,18 @@ static void mtk_thermal_init_bank(struct mtk_thermal *mt, int num,
mt->thermal_base + TEMP_PNPMUXADDR);

/* AHB value for auxadc enable */
- writel(BIT(MT8173_TEMP_AUXADC_CHANNEL), mt->thermal_base + TEMP_ADCEN);
+ writel(BIT(conf->auxadc_channel), mt->thermal_base + TEMP_ADCEN);

/* AHB address for auxadc enable (channel 0 immediate mode selected) */
writel(auxadc_phys_base + AUXADC_CON1_SET_V,
mt->thermal_base + TEMP_ADCENADDR);

/* AHB address for auxadc valid bit */
- writel(auxadc_phys_base + AUXADC_DATA(MT8173_TEMP_AUXADC_CHANNEL),
+ writel(auxadc_phys_base + AUXADC_DATA(conf->auxadc_channel),
mt->thermal_base + TEMP_ADCVALIDADDR);

/* AHB address for auxadc voltage output */
- writel(auxadc_phys_base + AUXADC_DATA(MT8173_TEMP_AUXADC_CHANNEL),
+ writel(auxadc_phys_base + AUXADC_DATA(conf->auxadc_channel),
mt->thermal_base + TEMP_ADCVOLTADDR);

/* read valid & voltage are at the same register */
@@ -407,11 +466,12 @@ static void mtk_thermal_init_bank(struct mtk_thermal *mt, int num,
writel(TEMP_ADCWRITECTRL_ADC_MUX_WRITE,
mt->thermal_base + TEMP_ADCWRITECTRL);

- for (i = 0; i < cfg->num_sensors; i++)
- writel(sensor_mux_values[cfg->sensors[i]],
- mt->thermal_base + sensing_points[i].adcpnp);
+ for (i = 0; i < conf->bank_data[num].num_sensors; i++)
+ writel(conf->sensor_mux_values[conf->bank_data[num].sensors[i]],
+ mt->thermal_base + conf->sensing_points[i].adcpnp);

- writel((1 << cfg->num_sensors) - 1, mt->thermal_base + TEMP_MONCTL0);
+ writel((1 << conf->bank_data[num].num_sensors) - 1,
+ mt->thermal_base + TEMP_MONCTL0);

writel(TEMP_ADCWRITECTRL_ADC_PNP_WRITE |
TEMP_ADCWRITECTRL_ADC_MUX_WRITE,
@@ -442,7 +502,7 @@ static int mtk_thermal_get_calibration_data(struct device *dev,

/* Start with default values */
mt->adc_ge = 512;
- for (i = 0; i < MT8173_NUM_SENSORS; i++)
+ for (i = 0; i < mt->conf->num_sensors; i++)
mt->vts[i] = 260;
mt->degc_cali = 40;
mt->o_slope = 0;
@@ -467,15 +527,15 @@ static int mtk_thermal_get_calibration_data(struct device *dev,
goto out;
}

- if (buf[0] & MT8173_CALIB_BUF0_VALID) {
- mt->adc_ge = MT8173_CALIB_BUF1_ADC_GE(buf[1]);
- mt->vts[MT8173_TS1] = MT8173_CALIB_BUF0_VTS_TS1(buf[0]);
- mt->vts[MT8173_TS2] = MT8173_CALIB_BUF0_VTS_TS2(buf[0]);
- mt->vts[MT8173_TS3] = MT8173_CALIB_BUF1_VTS_TS3(buf[1]);
- mt->vts[MT8173_TS4] = MT8173_CALIB_BUF2_VTS_TS4(buf[2]);
- mt->vts[MT8173_TSABB] = MT8173_CALIB_BUF2_VTS_TSABB(buf[2]);
- mt->degc_cali = MT8173_CALIB_BUF0_DEGC_CALI(buf[0]);
- mt->o_slope = MT8173_CALIB_BUF0_O_SLOPE(buf[0]);
+ if (buf[0] & CALIB_BUF0_VALID) {
+ mt->adc_ge = CALIB_BUF1_ADC_GE(buf[1]);
+ mt->vts[NVMEM_TS1] = CALIB_BUF0_VTS_TS1(buf[0]);
+ mt->vts[NVMEM_TS2] = CALIB_BUF0_VTS_TS2(buf[0]);
+ mt->vts[NVMEM_TS3] = CALIB_BUF1_VTS_TS3(buf[1]);
+ mt->vts[NVMEM_TS4] = CALIB_BUF2_VTS_TS4(buf[1]);
+ mt->vts[NVMEM_TS5] = CALIB_BUF2_VTS_TS5(buf[2]);
+ mt->degc_cali = CALIB_BUF0_DEGC_CALI(buf[0]);
+ mt->o_slope = CALIB_BUF0_O_SLOPE(buf[0]);
} else {
dev_info(dev, "Device not calibrated, using default calibration values\n");
}
@@ -486,18 +546,36 @@ out:
return ret;
}

+static const struct of_device_id mtk_thermal_of_match[] = {
+ {
+ .compatible = "mediatek,mt8173-thermal",
+ .data = (void *)&mt8173_thermal_data,
+ },
+ {
+ .compatible = "mediatek,mt2701-thermal",
+ .data = (void *)&mt2701_thermal_data,
+ }, {
+ },
+};
+MODULE_DEVICE_TABLE(of, mtk_thermal_of_match);
+
static int mtk_thermal_probe(struct platform_device *pdev)
{
int ret, i;
struct device_node *auxadc, *apmixedsys, *np = pdev->dev.of_node;
struct mtk_thermal *mt;
struct resource *res;
+ const struct of_device_id *of_id;
u64 auxadc_phys_base, apmixed_phys_base;

mt = devm_kzalloc(&pdev->dev, sizeof(*mt), GFP_KERNEL);
if (!mt)
return -ENOMEM;

+ of_id = of_match_device(mtk_thermal_of_match, &pdev->dev);
+ if (of_id)
+ mt->conf = (const struct mtk_thermal_data *)of_id->data;
+
mt->clk_peri_therm = devm_clk_get(&pdev->dev, "therm");
if (IS_ERR(mt->clk_peri_therm))
return PTR_ERR(mt->clk_peri_therm);
@@ -565,7 +643,7 @@ static int mtk_thermal_probe(struct platform_device *pdev)
goto err_disable_clk_auxadc;
}

- for (i = 0; i < MT8173_NUM_ZONES; i++)
+ for (i = 0; i < mt->conf->num_banks; i++)
mtk_thermal_init_bank(mt, i, apmixed_phys_base,
auxadc_phys_base);

@@ -592,13 +670,6 @@ static int mtk_thermal_remove(struct platform_device *pdev)
return 0;
}

-static const struct of_device_id mtk_thermal_of_match[] = {
- {
- .compatible = "mediatek,mt8173-thermal",
- }, {
- },
-};
-
static struct platform_driver mtk_thermal_driver = {
.probe = mtk_thermal_probe,
.remove = mtk_thermal_remove,
@@ -610,6 +681,7 @@ static struct platform_driver mtk_thermal_driver = {

module_platform_driver(mtk_thermal_driver);

+MODULE_AUTHOR("Dawei Chien <dawei.chien@mediatek.com>");
MODULE_AUTHOR("Sascha Hauer <s.hauer@pengutronix.de>");
MODULE_AUTHOR("Hanyi Wu <hanyi.wu@mediatek.com>");
MODULE_DESCRIPTION("Mediatek thermal driver");
--
1.7.9.5
\
 
 \ /
  Last update: 2016-07-07 11:41    [W:0.135 / U:0.384 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site