lkml.org 
[lkml]   [2016]   [Jul]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH v2] phy: add phy-hisi-inno-usb2
Date
Hi, Kishon
I am sorry. Please ignore the patch. The mail received maintainer incomplete and patch version is not correct.
I will send the patch again.

Thanks,
Pengcheng Li

> -----Original Message-----
> From: Lipengcheng
> Sent: Thursday, July 07, 2016 11:12 AM
> To: 'Kishon Vijay Abraham I'; linux-kernel@vger.kernel.org; Lidongpo
> Cc: Xuejiancheng; Zhangzhenxing (Christian, Device ChipSet)
> Subject: RE: [PATCH v2] phy: add phy-hisi-inno-usb2
>
> Hi, Kishon
>
> > -----Original Message-----
> > From: Kishon Vijay Abraham I [mailto:kishon@ti.com]
> > Sent: Monday, July 04, 2016 6:59 PM
> > To: Lipengcheng; linux-kernel@vger.kernel.org; Lidongpo
> > Subject: Re: [PATCH v2] phy: add phy-hisi-inno-usb2
> >
> > Hi,
> >
> > On Sunday 03 July 2016 12:20 PM, l00229106 wrote:
> > > Add support for inno usb2 phy integrated on some hisilicon SOCs.
> > >
> > > Signed-off-by: Pengcheng Li <lpc.li@hisilicon.com>
> > > ---
> > > .../devicetree/bindings/phy/phy-hisi-inno-usb2.txt | 48 ++++
> > > drivers/phy/Kconfig | 10 +
> > > drivers/phy/Makefile | 1 +
> > > drivers/phy/phy-hisi-inno-usb2.c | 298 +++++++++++++++++++++
> > > 4 files changed, 357 insertions(+)
> > > create mode 100644
> > > Documentation/devicetree/bindings/phy/phy-hisi-inno-usb2.txt
> > > create mode 100644 drivers/phy/phy-hisi-inno-usb2.c
> > >
> > > diff --git
> > > a/Documentation/devicetree/bindings/phy/phy-hisi-inno-usb2.txt
> > > b/Documentation/devicetree/bindings/phy/phy-hisi-inno-usb2.txt
> > > new file mode 100644
> > > index 0000000..59eaf73
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/phy/phy-hisi-inno-usb2.txt
> > > @@ -0,0 +1,48 @@
> > > +HiSilicon INNO USB2 PHY
> > > +-----------------------
> > > +Required properties:
> > > +- compatible: Should be "hisilicon,inno_usb2_phy"
> > > +- #phy-cells: Must be 0
> > > +- hisilicon,peripheral-syscon: Phandle of syscon used to control phy.
> > > +- hisilicon,reg-num: Number of phy registers which should be
> > > +configured at phy intialization stage
> > > +- hisilicon,reg-seq: Sequence of triplets of (address, value, delay-us).
> > > +The number of triplets is equal to "hisilicon,reg-num". Each
> > > +triplet is used to write one phy register. The delay-us cell
> > > +represents the delay time in microseconds to be applied after each write.
> > > +- clocks: Phandle and clock specifier pair for reference clock utmi_refclk.
> > > +- resets: List of phandle and reset specifier pairs for each reset
> > > +signal in reset-names.
> > > +- reset-names: Should be "por_rst" and "test_rst". The test_rst
> > > +only exists in some of SOCs, so it is optional.
> > > +
> > > +Phy node can includes up to four subnodes. Each subnode represents one port.
> > > +The required properties of port node are as follows:
> > > +- clocks: Phandle and clock specifier pair for utmi_clock.
> > > +- resets: List of phandle and reset specifier pairs for port reset and utmi reset.
> > > +- reset-names: List of reset signal names. Should be "port_rst" and "utmi_rst"
> > > +
> > > +Refer to phy/phy-bindings.txt for the generic PHY binding
> > > +properties
> > > +
> > > +Example:
> > > +usb_phy: phy {
> > > + compatible = "hisilicon,inno_usb2_phy";
> > > + #phy-cells = <0>;
> > > + hisilicon,peripheral-syscon = <&peri_ctrl>;
> > > + hisilicon,reg-num = <7>;
> > > + hisilicon,reg-seq = <0x80 0x800000 20>,
> > > + <0x80 0xa0060c 200>,
> > > + <0x80 0x80001c 20>,
> > > + <0x80 0xa0001c 20>,
> > > + <0x80 0x80060f 20>,
> > > + <0x80 0xa0060f 20>,
> > > + <0x80 0x800a4b 20>;
> > > + clocks = <&crg USB2_REF_CLK>;
> > > + resets = <&crg 0xb4 2>;
> > > + reset-names = "por_rst";
> > > + port0 {
> > > + clocks = <&crg USB2_UTMI0_CLK>;
> > > + resets = <&crg 0xb4 5>, <&crg 0xb4 1>;
> > > + reset-names = "port_rst", "utmi_rst";
> > > + };
> > > + };
> > > diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig index
> > > 26566db..8f043ca 100644
> > > --- a/drivers/phy/Kconfig
> > > +++ b/drivers/phy/Kconfig
> > > @@ -205,6 +205,16 @@ config PHY_EXYNOS5250_SATA
> > > SATA 3.0 Gb/s, SATA 6.0 Gb/s speeds. It supports one SATA host
> > > port to accept one SATA device.
> > >
> > > +config PHY_HISI_INNO_USB2
> > > + tristate "Hisilicon Inno USB2 PHY support"
> > > + depends on (ARCH_HISI) || COMPILE_TEST
> > > + select GENERIC_PHY
> > > + select MFD_SYSCON
> > > + help
> > > + Support for INNO PHY on Hisilicon Socs. This Phy supports
> > > + USB 1.5Mb/s, USB 12Mb/s, USB 480Mb/s speeds. It suppots one
> > > + USB host port to accept one USB device.
> > > +
> > > config PHY_HIX5HD2_SATA
> > > tristate "HIX5HD2 SATA PHY Driver"
> > > depends on ARCH_HIX5HD2 && OF && HAS_IOMEM diff --git
> > > a/drivers/phy/Makefile b/drivers/phy/Makefile index 24596a9..ef6a24b
> > > 100644
> > > --- a/drivers/phy/Makefile
> > > +++ b/drivers/phy/Makefile
> > > @@ -24,6 +24,7 @@ obj-$(CONFIG_TI_PIPE3) += phy-ti-pipe3.o
> > > obj-$(CONFIG_TWL4030_USB) += phy-twl4030-usb.o
> > > obj-$(CONFIG_PHY_EXYNOS5250_SATA) += phy-exynos5250-sata.o
> > > obj-$(CONFIG_PHY_HIX5HD2_SATA) += phy-hix5hd2-sata.o
> > > +obj-$(CONFIG_PHY_HISI_INNO_USB2) += phy-hisi-inno-usb2.o
> > > obj-$(CONFIG_PHY_HI6220_USB) += phy-hi6220-usb.o
> > > obj-$(CONFIG_PHY_MT65XX_USB3) += phy-mt65xx-usb3.o
> > > obj-$(CONFIG_PHY_SUN4I_USB) += phy-sun4i-usb.o
> > > diff --git a/drivers/phy/phy-hisi-inno-usb2.c
> > > b/drivers/phy/phy-hisi-inno-usb2.c
> > > new file mode 100644
> > > index 0000000..6930bb0
> > > --- /dev/null
> > > +++ b/drivers/phy/phy-hisi-inno-usb2.c
> > > @@ -0,0 +1,298 @@
> > > + /*
> > > + * HiSilicon INNO USB2 PHY Driver.
> > > + *
> > > + * Copyright (c) 2016 HiSilicon Technologies Co., Ltd.
> > > + *
> > > + * This program is free software; you can redistribute it and/or
> > > + modify
> > > + * it under the terms of the GNU General Public License as
> > > + published by
> > > + * the Free Software Foundation; either version 2 of the License,
> > > + or
> > > + * (at your option) any later version.
> > > + *
> > > + * This program is distributed in the hope that it will be useful,
> > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > > + * GNU General Public License for more details.
> > > + *
> > > + * You should have received a copy of the GNU General Public
> > > + License
> > > + * along with this program. If not, see <http://www.gnu.org/licenses/>.
> > > + */
> > > +
> > > +#include <linux/clk.h>
> > > +#include <linux/delay.h>
> > > +#include <linux/mfd/syscon.h>
> > > +#include <linux/module.h>
> > > +#include <linux/platform_device.h>
> > > +#include <linux/phy/phy.h>
> > > +#include <linux/regmap.h>
> > > +#include <linux/reset.h>
> > > +
> > > +#define MAX_PORTS 4
> > > +
> > > +struct hisi_inno_phy_port {
> > > + struct clk *utmi_clk;
> > > + struct reset_control *port_rst;
> > > + struct reset_control *utmi_rst;
> > > +};
> > > +
> > > +struct hisi_inno_phy_priv {
> > > + struct regmap *reg_peri;
> > > + struct clk *ref_clk;
> > > + struct reset_control *test_rst;
> > > + struct reset_control *por_rst;
> > > + struct reg_sequence *reg_seq;
> > > + u32 reg_num;
> > > + struct hisi_inno_phy_port *ports;
> > > + u8 port_num;
> > > +};
> > > +
> > > +static int hisi_inno_phy_setup(struct hisi_inno_phy_priv *priv) {
> > > + return regmap_multi_reg_write_bypassed(priv->reg_peri,
> > > + priv->reg_seq, priv->reg_num);
> > > +}
> > > +
> > > +static int hisi_inno_port_init(struct hisi_inno_phy_port *port) {
> > > + int ret = 0;
> > > +
> > > + reset_control_deassert(port->port_rst);
> > > + mdelay(2);
> > > +
> > > + ret = clk_prepare_enable(port->utmi_clk);
> > > + if (ret)
> > > + return ret;
> > > + udelay(200);
> > > +
> > > + reset_control_deassert(port->utmi_rst);
> > > + udelay(200);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static int hisi_inno_phy_init(struct phy *phy) {
> > > + struct hisi_inno_phy_priv *priv = phy_get_drvdata(phy);
> > > + int ret, port;
> > > +
> > > + ret = clk_prepare_enable(priv->ref_clk);
> > > + if (ret)
> > > + return ret;
> > > + udelay(100);
> > > +
> > > + if (priv->test_rst) {
> > > + reset_control_deassert(priv->test_rst);
> > > + udelay(100);
> > > + }
> > > +
> > > + reset_control_deassert(priv->por_rst);
> > > + udelay(300);
> > > +
> > > + /* config phy clk and phy eye diagram */
> > > + ret = hisi_inno_phy_setup(priv);
> > > + if (ret)
> > > + goto err_disable_ref_clk;
> > > +
> > > + for (port = 0; port < priv->port_num; port++) {
> > > + ret = hisi_inno_port_init(&priv->ports[port]);
> > > + if (ret)
> > > + goto err_disable_clks;
> > > + }
> > > +
> > > + return 0;
> > > +
> > > +err_disable_clks:
> > > + while (--port >= 0)
> > > + clk_disable_unprepare(priv->ports[port].utmi_clk);
> > > +err_disable_ref_clk:
> > > + clk_disable_unprepare(priv->ref_clk);
> > > +
> > > + return ret;
> > > +}
> > > +
> > > +static void hisi_inno_phy_disable(struct phy *phy) {
> > > + struct hisi_inno_phy_priv *priv = phy_get_drvdata(phy);
> > > + int i;
> > > +
> > > + for (i = 0; i < priv->port_num; i++)
> > > + clk_disable_unprepare(priv->ports[i].utmi_clk);
> > > +
> > > + clk_disable_unprepare(priv->ref_clk);
> > > +}
> > > +
> > > +static int hisi_inno_phy_of_get_ports(struct device *dev,
> > > + struct hisi_inno_phy_priv *priv) {
> > > + struct device_node *node = dev->of_node, *child;
> > > + int port = 0, ret = 0;
> > > +
> > > + priv->port_num = of_get_child_count(node);
> > > + if (priv->port_num > MAX_PORTS) {
> > > + dev_err(dev, "too many ports : %d (max = %d)\n",
> > > + priv->port_num, MAX_PORTS);
> > > + return -EINVAL;
> > > + }
> > > +
> > > + priv->ports = devm_kcalloc(dev, priv->port_num,
> > > + sizeof(struct hisi_inno_phy_port), GFP_KERNEL);
> > > + if (!priv->ports)
> > > + return -ENOMEM;
> > > +
> > > + for_each_child_of_node(node, child) {
> > > + struct hisi_inno_phy_port *phy_port = &priv->ports[port];
> > > +
> > > + phy_port->utmi_clk = of_clk_get(child, 0);
> > > + if (IS_ERR(phy_port->utmi_clk)) {
> > > + ret = PTR_ERR(phy_port->utmi_clk);
> > > + goto fail;
> > > + }
> > > +
> > > + phy_port->port_rst = of_reset_control_get(child, "port_rst");
> > > + if (IS_ERR(phy_port->port_rst)) {
> > > + ret = PTR_ERR(phy_port->port_rst);
> > > + clk_put(phy_port->utmi_clk);
> > > + goto fail;
> > > + }
> > > +
> > > + phy_port->utmi_rst = of_reset_control_get(child, "utmi_rst");
> > > + if (IS_ERR(phy_port->utmi_rst)) {
> > > + ret = PTR_ERR(phy_port->utmi_rst);
> > > + reset_control_put(phy_port->port_rst);
> > > + clk_put(phy_port->utmi_clk);
> > > + goto fail;
> > > + }
> > > + port++;
> > > + }
> > > +
> > > + return ret;
> > > +
> > > +fail:
> > > + while (--port >= 0) {
> > > + struct hisi_inno_phy_port *phy_port = &priv->ports[port];
> > > +
> > > + reset_control_put(phy_port->utmi_rst);
> > > + reset_control_put(phy_port->port_rst);
> > > + clk_put(phy_port->utmi_clk);
> > > + }
> > > + of_node_put(child);
> > > +
> > > + return ret;
> > > +}
> > > +
> > > +static struct phy_ops hisi_inno_phy_ops = {
> > > + .owner = THIS_MODULE,
> > > +};
> >
> > There is no phy ops here ^^^.
> > > +
> > > +static int hisi_inno_phy_probe(struct platform_device *pdev) {
> > > + struct phy_provider *phy_provider;
> > > + struct device *dev = &pdev->dev;
> > > + struct phy *phy;
> > > + struct hisi_inno_phy_priv *priv;
> > > + struct device_node *node = dev->of_node;
> > > + int ret = 0;
> > > +
> > > + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> > > + if (!priv)
> > > + return -ENOMEM;
> > > +
> > > + ret = of_property_read_u32(node, "hisilicon,reg-num", &priv->reg_num);
> > > + if (ret) {
> > > + dev_err(dev, "can't read the phy registers number!\n");
> > > + return ret;
> > > + }
> > > +
> > > + priv->reg_seq = devm_kcalloc(dev, priv->reg_num,
> > > + sizeof(struct reg_sequence), GFP_KERNEL);
> > > + if (!priv->reg_seq)
> > > + return -ENOMEM;
> > > +
> > > + ret = of_property_read_u32_array(node, "hisilicon,reg-seq",
> > > + (u32 *)priv->reg_seq, 3 * priv->reg_num);
> > > + if (ret) {
> > > + dev_err(dev, "can't read the phy offset and value!\n");
> > > + return ret;
> > > + }
> > > +
> > > + priv->reg_peri = syscon_regmap_lookup_by_phandle(node,
> > > + "hisilicon,peripheral-syscon");
> > > + if (IS_ERR(priv->reg_peri)) {
> > > + dev_err(dev, "no hisilicon,peripheral-syscon\n");
> > > + return PTR_ERR(priv->reg_peri);
> > > + }
> > > +
> > > + priv->ref_clk = devm_clk_get(dev, NULL);
> > > + if (IS_ERR(priv->ref_clk))
> > > + return PTR_ERR(priv->ref_clk);
> > > +
> > > + priv->por_rst = devm_reset_control_get(dev, "por_rst");
> > > + if (IS_ERR(priv->por_rst))
> > > + return PTR_ERR(priv->por_rst);
> > > +
> > > + priv->test_rst = devm_reset_control_get(dev, "test_rst");
> > > + if (IS_ERR(priv->test_rst))
> > > + priv->test_rst = NULL;
> > > +
> > > + ret = hisi_inno_phy_of_get_ports(dev, priv);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + phy = devm_phy_create(dev, NULL, &hisi_inno_phy_ops);
> > > + if (IS_ERR(phy))
> > > + return PTR_ERR(phy);
> >
> > But you register it with the phy framework. Do you really intend to use the PHY framework for some reason.
> >
> I do not use the PHY framework. I will delete the code about the PHY framework in next patch.
>
> > Thanks
> > Kishon
>
> Thanks
> Pengcheng Li
\
 
 \ /
  Last update: 2016-07-07 06:21    [W:0.052 / U:3.176 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site