lkml.org 
[lkml]   [2016]   [Jul]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH v3 2/2] pci/aer: interrupt fixup in the quirk
Date
Hi Dongdong,

The patch were intend to fixup the NXP layerscape serial SOC and were tested ok.
I am not clear what platform are you trying to fix.
The problem on your board may be as below comments:


> -----Original Message-----
> From: Dongdong Liu [mailto:liudongdong3@huawei.com]
> Sent: Monday, July 04, 2016 4:44 PM
> To: Po Liu; linux-pci@vger.kernel.org; linux-arm-
> kernel@lists.infradead.org; linux-kernel@vger.kernel.org;
> devicetree@vger.kernel.org
> Cc: Bjorn Helgaas; Shawn Guo; Marc Zyngier; Rob Herring; Roy Zang;
> Mingkai Hu; Stuart Yoder; Yang-Leo Li; Arnd Bergmann; Minghuan Lian;
> Murali Karicheri; Linuxarm
> Subject: Re: [PATCH v3 2/2] pci/aer: interrupt fixup in the quirk
>
> Hi Po
>
> I found a problem with the similar patch. as the below log.
>
> [ 4.287060] pci 0000:80:00.0: quirk_aer_interrupt dev->irq 416
> [ 4.293778] pcieport 0000:80:00.0: pci_device_probe in
> [ 4.299605] pcieport 0000:80:00.0: of_irq_parse_pci() failed with
> rc=-22
> [ 4.307209] pcieport 0000:80:00.0: init_service_irqs dev->irq 0
>
> The fucntions are called as below sequence.
> 1. quirk_aer_interrupt, get the aer dev->irq 416.

This code quirk_aer_interrupt() should be run at pci_fixup_device(pci_fixup_final) which is in the pci_bus_add_devices()

> 2. pci_device_probe->of_irq_parse_pci, of_irq_parse_pci() failed, then
> dev->irq changed to 0.

pci_device_probe->of_irq_parse_pci which in the pci_scan_child_bus() run before pci_bus_add_devices(). See dw_pcie_host_init().
Apparently , your quirk_aer_interrupt() is running before the dev->irq assignment in the of_irq_parse_pci().

So make sure your configure the quirk_aer_interrupt() run in the FINAL stage in the quirk.c OR check your host driver which you are using.


>
> So this patch could not work with aer.
>
> Thanks
> Dongdong
> 在 2016/6/14 16:24, Po Liu 写道:
> > On some platforms, root port doesn't support MSI/MSI-X/INTx in RC mode.
> > When chip support the aer interrupt with none MSI/MSI-X/INTx mode,
> > maybe there is interrupt line for aer pme etc. Search the interrupt
> > number in the fdt file. Then fixup the dev->irq with it.
> >
> > Signed-off-by: Po Liu <po.liu@nxp.com>
> > ---
> > changes for V3:
> > - Move to quirk;
> > - Only correct the irq in RC mode;
> >
> > drivers/pci/quirks.c | 29 +++++++++++++++++++++++++++++
> > 1 file changed, 29 insertions(+)
> >
> > diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c index
> > ee72ebe..8b39cce 100644
> > --- a/drivers/pci/quirks.c
> > +++ b/drivers/pci/quirks.c
> > @@ -25,6 +25,7 @@
> > #include <linux/sched.h>
> > #include <linux/ktime.h>
> > #include <linux/mm.h>
> > +#include <linux/of_irq.h>
> > #include <asm/dma.h> /* isa_dma_bridge_buggy */
> > #include "pci.h"
> >
> > @@ -4419,3 +4420,31 @@ static void quirk_intel_qat_vf_cap(struct
> pci_dev *pdev)
> > }
> > }
> > DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x443,
> > quirk_intel_qat_vf_cap);
> > +
> > +/* If root port doesn't support MSI/MSI-X/INTx in RC mode,
> > + * but use standalone irq. Read the device tree for the aer
> > + * interrupt number.
> > + */
> > +static void quirk_aer_interrupt(struct pci_dev *dev) {
> > + int ret;
> > + u8 header_type;
> > + struct device_node *np = NULL;
> > +
> > + /* Only for the RC mode device */
> > + pci_read_config_byte(dev, PCI_HEADER_TYPE, &header_type);
> > + if ((header_type & 0x7F) != PCI_HEADER_TYPE_BRIDGE)
> > + return;
> > +
> > + if (dev->bus->dev.of_node)
> > + np = dev->bus->dev.of_node;
> > +
> > + if (IS_ENABLED(CONFIG_OF_IRQ) && np) {
> > + ret = of_irq_get_byname(np, "aer");
> > + if (ret > 0) {
> > + dev->no_msi = 1;
> > + dev->irq = ret;
> > + }
> > + }
> > +}
> > +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_FREESCALE, PCI_ANY_ID,
> > +quirk_aer_interrupt);
> >
>

\
 
 \ /
  Last update: 2016-07-05 05:41    [W:0.191 / U:12.804 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site