lkml.org 
[lkml]   [2016]   [Jul]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v4 1/2] Documentation: bindings: add dt doc for Rockchip PCIe controller
From
Date
在 2016/7/2 10:25, Brian Norris 写道:
> Hi,
>
> On Fri, Jul 01, 2016 at 02:01:09PM +0100, Marc Zyngier wrote:
>> On 01/07/16 02:24, Shawn Lin wrote:
>>> This patch adds a binding that describes the Rockchip PCIe controller
>>> found on Rockchip SoCs PCIe interface.
>>>
>>> Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
>>>
>>> ---
>>>
>>> Changes in v4:
>>> - fix example of adding intermediate interrupt controller for pcie
>>> legacy interrrupt
>>>
>>> Changes in v3:
>>> - fix example dts code suggested by Rob and Marc
>>> - remove driver's behaviour of regulator
>>>
>>> Changes in v2:
>>> - fix lots clk/reset stuff suggested by Heiko
>>> - remove msi-parent and add msi-map suggested by Marc
>>> - drop phy related stuff
>>> - some others minor fixes
>>>
>>> .../devicetree/bindings/pci/rockchip-pcie.txt | 91 ++++++++++++++++++++++
>>> 1 file changed, 91 insertions(+)
>>> create mode 100644 Documentation/devicetree/bindings/pci/rockchip-pcie.txt
>>>
>>> diff --git a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt
>>> new file mode 100644
>>> index 0000000..8092fc5
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt
>>> @@ -0,0 +1,91 @@
>>> +* Rockchip AXI PCIe Root Port Bridge DT description
>>> +
>>> +Required properties:
>>> +- #address-cells: Address representation for root ports, set to <3>
>>> +- #size-cells: Size representation for root ports, set to <2>
>>> +- #interrupt-cells: specifies the number of cells needed to encode an
>>> + interrupt source. The value must be 1.
>
> I think this propoerty should be in a separate section, since it's going
> under a sub-node (not the main node). Right?
>

main node also need it.

>>> +- compatible: Should contain "rockchip,rk3399-pcie"
>>> +- reg: Two register ranges as listed in the reg-names property
>>> +- reg-names: Must include the following names
>>> + - "axi-base"
>>> + - "apb-base"
>>> +- clocks: Must contain an entry for each entry in clock-names.
>>> + See ../clocks/clock-bindings.txt for details.
>>> +- clock-names: Must include the following entries:
>>> + - "aclk"
>>> + - "aclk-perf"
>>> + - "hclk"
>>> + - "pm"
>>> +- msi-map: Maps a Requester ID to an MSI controller and associated.
>>> + See ./pci-msi.txt
>>> +- phys: From PHY bindings: Phandle for the Generic PHY for PCIe.
>>> +- phy-names: MUST be "pcie-phy".
>>> +- interrupts: Three interrupt entries must be specified.
>>> +- interrupt-names: Must include the following names
>>> + - "sys"
>>> + - "legacy"
>>> + - "client"
>>> +- resets: Must contain five entries for each entry in reset-names.
>>> + See ../reset/reset.txt for details.
>>> +- reset-names: Must include the following names
>>> + - "core"
>>> + - "mgmt"
>>> + - "mgmt-sticky"
>>> + - "pipe"
>>> +- pinctrl-names : The pin control state names
>>> +- pinctrl-0: The "default" pinctrl state
>>> +- interrupt-map-mask and interrupt-map: standard PCI properties
>>> +- interrupt-controller: identifies the node as an interrupt controller
>
> Same with this property.
>
>>> +
>>> +Optional Property:
>>> +- ep-gpios: contain the entry for pre-reset gpio
>>> +- num-lanes: number of lanes to use
>>> +- vpcie3v3-supply: The phandle to the 3.3v regulator to use for pcie.
>>> +- vpcie1v8-supply: The phandle to the 1.8v regulator to use for pcie.
>>> +- vpcie0v9-supply: The phandle to the 0.9v regulator to use for pcie.
>
> e.g., you might start a new section here describing how this controller
> acts as an intermediate IRQ controller, and that the
> interrupt-controller-related properties should be placed under a subnode.
> (Did you also need an interrupt-parent property? I'm a little fuzzy on
> the details myself, actually...)

ok I will do it.

>
>>> +
>>> +Example:
>>> +
>>> +pcie0: pcie@f8000000 {
>>> + compatible = "rockchip,rk3399-pcie";
>>> + #address-cells = <3>;
>>> + #size-cells = <2>;
>>> + clocks = <&cru ACLK_PCIE>, <&cru ACLK_PERF_PCIE>,
>>> + <&cru PCLK_PCIE>, <&cru SCLK_PCIE_PM>;
>>> + clock-names = "aclk", "aclk-perf",
>>> + "hclk", "pm";
>>> + bus-range = <0x0 0x1>;
>>> + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>,
>>> + <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
>>> + interrupt-names = "sys", "legacy", "client";
>>> + assigned-clocks = <&cru SCLK_PCIEPHY_REF>;
>>> + assigned-clock-parents = <&cru SCLK_PCIEPHY_REF100M>;
>>> + assigned-clock-rates = <100000000>;
>>> + ep-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
>>> + ranges = <0x83000000 0x0 0xfa000000 0x0 0xfa000000 0x0 0x600000
>>> + 0x81000000 0x0 0xfa600000 0x0 0xfa600000 0x0 0x100000>;
>>> + num-lanes = <4>;
>>> + msi-map = <0x0 &its 0x0 0x1000>;
>>> + reg = < 0x0 0xf8000000 0x0 0x2000000 >, < 0x0 0xfd000000 0x0 0x1000000 >;
>>> + reg-names = "axi-base", "apb-base";
>>> + resets = <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>,
>>> + <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE>;
>>> + reset-names = "core", "mgmt", "mgmt-sticky", "pipe";
>>> + phys = <&pcie_phy>;
>>> + phy-names = "pcie-phy";
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&pcie_clkreq>;
>>> + #interrupt-cells = <1>;
>>> + interrupt-controller;
>>
>> So the pcie node itself is an interrupt controller...
>>
>>> + interrupt-map-mask = <0 0 0 7>;
>>> + interrupt-map = <0 0 0 1 &pcie0_intc 1>,
>>> + <0 0 0 2 &pcie0_intc 2>,
>>> + <0 0 0 3 &pcie0_intc 3>,
>>> + <0 0 0 4 &pcie0_intc 4>;
>>> + pcie0_intc: interrupt-controller {
>>> + interrupt-controller;
>>> + #address-cells = <0>;
>>> + #interrupt-cells = <1>;
>>> + };
>>
>> But there's also another here. I just don't understand how it works.
>
> I believe the repeat of #interrupt-cells and interrupt-controller in the
> pcie@ node is a mistake. They should only be in the 'interrupt-controller'
> subnode. And in case this is what you're asking about... the subnode was
> present in v1 but was removed at your request:

Sorry for this noise, I will fix them.

>
> From Marc, in https://patchwork.kernel.org/patch/9129183/:
>>> +static int rockchip_pcie_init_irq_domain(struct rockchip_pcie_port *pp)
>>> +{
>>> + struct device *dev = pp->dev;
>>> + struct device_node *node = dev->of_node;
>>> + struct device_node *pcie_intc_node = of_get_next_child(node, NULL);
>>
>> That's really ugly, as it depends on the layout of your DT.
>>
>>> +
>>> + if (!pcie_intc_node) {
>>> + dev_err(dev, "No PCIe Intc node found\n");
>>> + return PTR_ERR(pcie_intc_node);
>>> + }
>>> + pp->irq_domain = irq_domain_add_linear(pcie_intc_node, 4,
>>> + &intx_domain_ops, pp);
>>
>> Why can't you just register your host controller as the interrupt
>> controller? You don't need an intermediate node for that.
>
> But then in v3, Arnd concluded it actually *should* be used:
>
> From Arnd, in https://patchwork.kernel.org/patch/9179763/:
>> On Thursday, June 16, 2016 4:01:12 PM CEST Wenrui Li wrote:
>>> 在 2016/6/16 15:00, Arnd Bergmann 写道:
>>>> On Thursday, June 16, 2016 9:50:21 AM CEST Shawn Lin wrote:
>>>>
>>>>> + reset-names = "core", "mgmt", "mgmt-sticky", "pipe";
>>>>> + phys = <&pcie_phy>;
>>>>> + phy-names = "pcie-phy";
>>>>> + pinctrl-names = "default";
>>>>> + pinctrl-0 = <&pcie_clkreq>;
>>>>> + #interrupt-cells = <1>;
>>>>> + interrupt-controller;
>>>>> + interrupt-map-mask = <0 0 0 7>;
>>>>> + interrupt-map = <0 0 0 1 &pcie0 1>,
>>>>> + <0 0 0 2 &pcie0 2>,
>>>>> + <0 0 0 3 &pcie0 3>,
>>>>> + <0 0 0 4 &pcie0 4>;
>>>>> +};
>>>>>
>>>>
>>>> One thing that came up in the review of the new Marvell PCIe driver is that it's
>>>> most likely invalid for a device node to have both "interrupt-controller"
>>>> and "interrupt-map" properties. I originally thought this was a nice way to
>>>> handle embedded irqchips within the PCIe host, but it only really works
>>>> by coincidence with the current kernel, and only as long as the hwirq number
>>>> of the irqchip matches the integer representation of the irq line in the root
>>>> bridge (which it does in the example above).
>>>>
>>>> For that driver we concluded that it would be less of a hack to have the
>>>> irqchip as a child node of the PCIe host after all (just not with
>>>> device_type="pci" of course), and that makes the translation work as
>>>> expected.
>>>>
>>>> Arnd
>>>>
>>>
>>> Original driver have an irqchip as child node. But Marc suggested don't
>>> need an intermediate node here.
>>> Now the conclusion is to retain the child node?
>>
>> That is at least my view of the situation, sorry for the mixed messages
>> you have been getting. Marc, Rob, do you agree with my finding?
>
> Rob and others agreed with the subnode. So, I hope you don't disagree in
> principle, and are only confused by the duplicate properties?
>
> Regards,
> Brian
>
> _______________________________________________
> Linux-rockchip mailing list
> Linux-rockchip@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-rockchip
>


--
Best Regards
Shawn Lin

\
 
 \ /
  Last update: 2016-07-05 04:41    [W:0.104 / U:4.464 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site