lkml.org 
[lkml]   [2016]   [Jul]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v7 2/2] [media] atmel-isc: DT binding for Image Sensor Controller driver
Date
DT binding documentation for ISC driver.

Signed-off-by: Songjun Wu <songjun.wu@microchip.com>
---

Changes in v7: None
Changes in v6:
- Add "iscck" and "gck" to clock-names.

Changes in v5:
- Add clock-output-names.

Changes in v4:
- Remove the isc clock nodes.

Changes in v3:
- Remove the 'atmel,sensor-preferred'.
- Modify the isc clock node according to the Rob's remarks.

Changes in v2:
- Remove the unit address of the endpoint.
- Add the unit address to the clock node.
- Avoid using underscores in node names.
- Drop the "0x" in the unit address of the i2c node.
- Modify the description of 'atmel,sensor-preferred'.
- Add the description for the ISC internal clock.

.../devicetree/bindings/media/atmel-isc.txt | 65 ++++++++++++++++++++++
1 file changed, 65 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/atmel-isc.txt

diff --git a/Documentation/devicetree/bindings/media/atmel-isc.txt b/Documentation/devicetree/bindings/media/atmel-isc.txt
new file mode 100644
index 0000000..bbe0e87c
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/atmel-isc.txt
@@ -0,0 +1,65 @@
+Atmel Image Sensor Controller (ISC)
+----------------------------------------------
+
+Required properties for ISC:
+- compatible
+ Must be "atmel,sama5d2-isc".
+- reg
+ Physical base address and length of the registers set for the device.
+- interrupts
+ Should contain IRQ line for the ISC.
+- clocks
+ List of clock specifiers, corresponding to entries in
+ the clock-names property;
+ Please refer to clock-bindings.txt.
+- clock-names
+ Required elements: "hclock", "iscck", "gck".
+- #clock-cells
+ Should be 0.
+- clock-output-names
+ Should be "isc-mck".
+- pinctrl-names, pinctrl-0
+ Please refer to pinctrl-bindings.txt.
+
+ISC supports a single port node with parallel bus. It should contain one
+'port' child node with child 'endpoint' node. Please refer to the bindings
+defined in Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+isc: isc@f0008000 {
+ compatible = "atmel,sama5d2-isc";
+ reg = <0xf0008000 0x4000>;
+ interrupts = <46 IRQ_TYPE_LEVEL_HIGH 5>;
+ clocks = <&isc_clk>, <&iscck>, <&isc_gclk>;
+ clock-names = "hclock", "iscck", "gck";
+ #clock-cells = <0>;
+ clock-output-names = "isc-mck";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_isc_base &pinctrl_isc_data_8bit &pinctrl_isc_data_9_10 &pinctrl_isc_data_11_12>;
+
+ port {
+ isc_0: endpoint {
+ remote-endpoint = <&ov7740_0>;
+ hsync-active = <1>;
+ vsync-active = <0>;
+ pclk-sample = <1>;
+ };
+ };
+};
+
+i2c1: i2c@fc028000 {
+ ov7740: camera@21 {
+ compatible = "ovti,ov7740";
+ reg = <0x21>;
+ clocks = <&isc>;
+ clock-names = "xvclk";
+ assigned-clocks = <&isc>;
+ assigned-clock-rates = <24000000>;
+
+ port {
+ ov7740_0: endpoint {
+ remote-endpoint = <&isc_0>;
+ };
+ };
+ };
+};
--
2.7.4
\
 
 \ /
  Last update: 2016-07-29 10:41    [W:0.073 / U:0.116 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site