lkml.org 
[lkml]   [2016]   [Jul]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v6 1/2] led: is31fl319x: 1/3/6/9-channel light effect led driver
Tweaked the tabulation of macro values a bit more and applied
the patches to the for-4.9 branch of linux-leds.git.

Thanks,
Jacek Anaszewski

On 07/19/2016 01:47 PM, H. Nikolaus Schaller wrote:
> This is a driver for the Integrated Silicon Solution Inc. LED driver
> chips series IS31FL319x. They can drive 1, 3, 6 or up to 9
> LEDs.
>
> Each LED is individually controllable in brightness (through pwm)
> in 256 steps so that RGB LEDs can show any of ca. 16 Mio colors.
>
> The maximum current of the LEDs can be programmed and limited to
> 5 .. 40mA through a device tree property.
>
> The chip is connected through I2C and can have one of 4 addresses
> in the range 0x64 .. 0x67 depending on how the AD pin is connected. The
> address is defined by the reg property as usual.
>
> The chip also has a shutdown input which could be connected to a GPIO,
> but this driver uses software shutdown if all LEDs are inactivated.
>
> The chip also has breathing and audio features which are not fully
> supported by this driver.
>
> Tested-on: OMAP5 based Pyra handheld prototype.
> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
> Signed-off-by: Andrey Utkin <andrey_utkin@fastmail.com>
> ---
> drivers/leds/Kconfig | 12 ++
> drivers/leds/Makefile | 1 +
> drivers/leds/leds-is31fl319x.c | 450 +++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 463 insertions(+)
> create mode 100644 drivers/leds/leds-is31fl319x.c
>
> diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
> index 5ae2834..6439a7d 100644
> --- a/drivers/leds/Kconfig
> +++ b/drivers/leds/Kconfig
> @@ -570,6 +570,18 @@ config LEDS_SEAD3
> This driver can also be built as a module. If so the module
> will be called leds-sead3.
>
> +config LEDS_IS31FL319X
> + tristate "LED Support for ISSI IS31FL319x I2C LED controller family"
> + depends on LEDS_CLASS && I2C && OF
> + select REGMAP_I2C
> + help
> + This option enables support for LEDs connected to ISSI IS31FL319x
> + fancy LED driver chips accessed via the I2C bus.
> + Driver supports individual PWM brightness control for each channel.
> +
> + This driver can also be built as a module. If so the module will be
> + called leds-is31fl319x.
> +
> config LEDS_IS31FL32XX
> tristate "LED support for ISSI IS31FL32XX I2C LED controller family"
> depends on LEDS_CLASS && I2C && OF
> diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
> index cb2013d..b6ce9f9 100644
> --- a/drivers/leds/Makefile
> +++ b/drivers/leds/Makefile
> @@ -66,6 +66,7 @@ obj-$(CONFIG_LEDS_MENF21BMC) += leds-menf21bmc.o
> obj-$(CONFIG_LEDS_KTD2692) += leds-ktd2692.o
> obj-$(CONFIG_LEDS_POWERNV) += leds-powernv.o
> obj-$(CONFIG_LEDS_SEAD3) += leds-sead3.o
> +obj-$(CONFIG_LEDS_IS31FL319X) += leds-is31fl319x.o
> obj-$(CONFIG_LEDS_IS31FL32XX) += leds-is31fl32xx.o
>
> # LED SPI Drivers
> diff --git a/drivers/leds/leds-is31fl319x.c b/drivers/leds/leds-is31fl319x.c
> new file mode 100644
> index 0000000..dbdcfdd
> --- /dev/null
> +++ b/drivers/leds/leds-is31fl319x.c
> @@ -0,0 +1,450 @@
> +/*
> + * Copyright 2015-16 Golden Delicious Computers
> + *
> + * Author: Nikolaus Schaller <hns@goldelico.com>
> + *
> + * This file is subject to the terms and conditions of version 2 of
> + * the GNU General Public License. See the file COPYING in the main
> + * directory of this archive for more details.
> + *
> + * LED driver for the IS31FL319{0,1,3,6,9} to drive 1, 3, 6 or 9 light
> + * effect LEDs.
> + *
> + */
> +
> +#include <linux/err.h>
> +#include <linux/i2c.h>
> +#include <linux/leds.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/regmap.h>
> +#include <linux/slab.h>
> +
> +/* register numbers */
> +#define IS31FL319X_SHUTDOWN 0x00
> +#define IS31FL319X_CTRL1 0x01
> +#define IS31FL319X_CTRL2 0x02
> +#define IS31FL319X_CONFIG1 0x03
> +#define IS31FL319X_CONFIG2 0x04
> +#define IS31FL319X_RAMP_MODE 0x05
> +#define IS31FL319X_BREATH_MASK 0x06
> +#define IS31FL319X_PWM(channel) (0x07 + channel)
> +#define IS31FL319X_DATA_UPDATE 0x10
> +#define IS31FL319X_T0(channel) (0x11 + channel)
> +#define IS31FL319X_T123_1 0x1a
> +#define IS31FL319X_T123_2 0x1b
> +#define IS31FL319X_T123_3 0x1c
> +#define IS31FL319X_T4(channel) (0x1d + channel)
> +#define IS31FL319X_TIME_UPDATE 0x26
> +#define IS31FL319X_RESET 0xff
> +
> +#define IS31FL319X_REG_CNT (IS31FL319X_RESET + 1)
> +
> +#define IS31FL319X_MAX_LEDS 9
> +
> +/* CS (Current Setting) in CONFIG2 register */
> +#define IS31FL319X_CONFIG2_CS_SHIFT 4
> +#define IS31FL319X_CONFIG2_CS_MASK 0x7
> +#define IS31FL319X_CONFIG2_CS_STEP_REF 12
> +
> +#define IS31FL319X_CURRENT_MIN ((u32)5000)
> +#define IS31FL319X_CURRENT_MAX ((u32)40000)
> +#define IS31FL319X_CURRENT_STEP ((u32)5000)
> +#define IS31FL319X_CURRENT_DEFAULT ((u32)20000)
> +
> +/* Audio gain in CONFIG2 register */
> +#define IS31FL319X_AUDIO_GAIN_DB_MAX ((u32)21)
> +#define IS31FL319X_AUDIO_GAIN_DB_STEP ((u32)3)
> +
> +/*
> + * regmap is used as a cache of chip's register space,
> + * to avoid reading back brightness values from chip,
> + * which is known to hang.
> + */
> +struct is31fl319x_chip {
> + const struct is31fl319x_chipdef *cdef;
> + struct i2c_client *client;
> + struct regmap *regmap;
> + struct mutex lock;
> + u32 audio_gain_db;
> +
> + struct is31fl319x_led {
> + struct is31fl319x_chip *chip;
> + struct led_classdev cdev;
> + u32 max_microamp;
> + bool configured;
> + } leds[IS31FL319X_MAX_LEDS];
> +};
> +
> +struct is31fl319x_chipdef {
> + int num_leds;
> +};
> +
> +static const struct is31fl319x_chipdef is31fl3190_cdef = {
> + .num_leds = 1,
> +};
> +
> +static const struct is31fl319x_chipdef is31fl3193_cdef = {
> + .num_leds = 3,
> +};
> +
> +static const struct is31fl319x_chipdef is31fl3196_cdef = {
> + .num_leds = 6,
> +};
> +
> +static const struct is31fl319x_chipdef is31fl3199_cdef = {
> + .num_leds = 9,
> +};
> +
> +static const struct of_device_id of_is31fl319x_match[] = {
> + { .compatible = "issi,is31fl3190", .data = &is31fl3190_cdef, },
> + { .compatible = "issi,is31fl3191", .data = &is31fl3190_cdef, },
> + { .compatible = "issi,is31fl3193", .data = &is31fl3193_cdef, },
> + { .compatible = "issi,is31fl3196", .data = &is31fl3196_cdef, },
> + { .compatible = "issi,is31fl3199", .data = &is31fl3199_cdef, },
> + { .compatible = "si-en,sn3199", .data = &is31fl3199_cdef, },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, of_is31fl319x_match);
> +
> +static int is31fl319x_brightness_set(struct led_classdev *cdev,
> + enum led_brightness brightness)
> +{
> + struct is31fl319x_led *led = container_of(cdev, struct is31fl319x_led,
> + cdev);
> + struct is31fl319x_chip *is31 = led->chip;
> + int chan = led - is31->leds;
> + int ret;
> + int i;
> + u8 ctrl1 = 0, ctrl2 = 0;
> +
> + dev_dbg(&is31->client->dev, "%s %d: %d\n", __func__, chan, brightness);
> +
> + mutex_lock(&is31->lock);
> +
> + /* update PWM register */
> + ret = regmap_write(is31->regmap, IS31FL319X_PWM(chan), brightness);
> + if (ret < 0)
> + goto out;
> +
> + /* read current brightness of all PWM channels */
> + for (i = 0; i < is31->cdef->num_leds; i++) {
> + unsigned int pwm_value;
> + bool on;
> +
> + /*
> + * since neither cdev nor the chip can provide
> + * the current setting, we read from the regmap cache
> + */
> +
> + ret = regmap_read(is31->regmap, IS31FL319X_PWM(i), &pwm_value);
> + dev_dbg(&is31->client->dev, "%s read %d: ret=%d: %d\n",
> + __func__, i, ret, pwm_value);
> + on = ret >= 0 && pwm_value > LED_OFF;
> +
> + if (i < 3)
> + ctrl1 |= on << i; /* 0..2 => bit 0..2 */
> + else if (i < 6)
> + ctrl1 |= on << (i + 1); /* 3..5 => bit 4..6 */
> + else
> + ctrl2 |= on << (i - 6); /* 6..8 => bit 0..2 */
> + }
> +
> + if (ctrl1 > 0 || ctrl2 > 0) {
> + dev_dbg(&is31->client->dev, "power up %02x %02x\n",
> + ctrl1, ctrl2);
> + regmap_write(is31->regmap, IS31FL319X_CTRL1, ctrl1);
> + regmap_write(is31->regmap, IS31FL319X_CTRL2, ctrl2);
> + /* update PWMs */
> + regmap_write(is31->regmap, IS31FL319X_DATA_UPDATE, 0x00);
> + /* enable chip from shut down */
> + ret = regmap_write(is31->regmap, IS31FL319X_SHUTDOWN, 0x01);
> + } else {
> + dev_dbg(&is31->client->dev, "power down\n");
> + /* shut down (no need to clear CTRL1/2) */
> + ret = regmap_write(is31->regmap, IS31FL319X_SHUTDOWN, 0x00);
> + }
> +
> +out:
> + mutex_unlock(&is31->lock);
> +
> + return ret;
> +}
> +
> +static int is31fl319x_parse_child_dt(const struct device *dev,
> + const struct device_node *child,
> + struct is31fl319x_led *led)
> +{
> + struct led_classdev *cdev = &led->cdev;
> + int ret;
> +
> + if (of_property_read_string(child, "label", &cdev->name))
> + cdev->name = child->name;
> +
> + ret = of_property_read_string(child, "linux,default-trigger",
> + &cdev->default_trigger);
> + if (ret < 0 && ret != -EINVAL) /* is optional */
> + return ret;
> +
> + led->max_microamp = IS31FL319X_CURRENT_DEFAULT;
> + ret = of_property_read_u32(child, "led-max-microamp",
> + &led->max_microamp);
> + if (!ret) {
> + if (led->max_microamp < IS31FL319X_CURRENT_MIN)
> + return -EINVAL; /* not supported */
> + led->max_microamp = min(led->max_microamp,
> + IS31FL319X_CURRENT_MAX);
> + }
> +
> + return 0;
> +}
> +
> +static int is31fl319x_parse_dt(struct device *dev,
> + struct is31fl319x_chip *is31)
> +{
> + struct device_node *np = dev->of_node, *child;
> + const struct of_device_id *of_dev_id;
> + int count;
> + int ret;
> +
> + if (!np)
> + return -ENODEV;
> +
> + of_dev_id = of_match_device(of_is31fl319x_match, dev);
> + if (!of_dev_id) {
> + dev_err(dev, "Failed to match device with supported chips\n");
> + return -EINVAL;
> + }
> +
> + is31->cdef = of_dev_id->data;
> +
> + count = of_get_child_count(np);
> +
> + dev_dbg(dev, "probe %s with %d leds defined in DT\n",
> + of_dev_id->compatible, count);
> +
> + if (!count || count > is31->cdef->num_leds) {
> + dev_err(dev, "Number of leds defined must be between 1 and %u\n",
> + is31->cdef->num_leds);
> + return -ENODEV;
> + }
> +
> + for_each_child_of_node(np, child) {
> + struct is31fl319x_led *led;
> + u32 reg;
> +
> + ret = of_property_read_u32(child, "reg", &reg);
> + if (ret) {
> + dev_err(dev, "Failed to read led 'reg' property\n");
> + goto put_child_node;
> + }
> +
> + if (reg < 1 || reg > is31->cdef->num_leds) {
> + dev_err(dev, "invalid led reg %u\n", reg);
> + ret = -EINVAL;
> + goto put_child_node;
> + }
> +
> + led = &is31->leds[reg - 1];
> +
> + if (led->configured) {
> + dev_err(dev, "led %u is already configured\n", reg);
> + ret = -EINVAL;
> + goto put_child_node;
> + }
> +
> + ret = is31fl319x_parse_child_dt(dev, child, led);
> + if (ret) {
> + dev_err(dev, "led %u DT parsing failed\n", reg);
> + goto put_child_node;
> + }
> +
> + led->configured = true;
> + }
> +
> + is31->audio_gain_db = 0;
> + ret = of_property_read_u32(np, "audio-gain-db", &is31->audio_gain_db);
> + if (!ret)
> + is31->audio_gain_db = min(is31->audio_gain_db,
> + IS31FL319X_AUDIO_GAIN_DB_MAX);
> +
> + return 0;
> +
> +put_child_node:
> + of_node_put(child);
> + return ret;
> +}
> +
> +static bool is31fl319x_readable_reg(struct device *dev, unsigned int reg)
> +{ /* we have no readable registers */
> + return false;
> +}
> +
> +static bool is31fl319x_volatile_reg(struct device *dev, unsigned int reg)
> +{ /* volatile registers are not cached */
> + switch (reg) {
> + case IS31FL319X_DATA_UPDATE:
> + case IS31FL319X_TIME_UPDATE:
> + case IS31FL319X_RESET:
> + return true; /* always write-through */
> + default:
> + return false;
> + }
> +}
> +
> +static const struct reg_default is31fl319x_reg_defaults[] = {
> + { IS31FL319X_CONFIG1, 0x00},
> + { IS31FL319X_CONFIG2, 0x00},
> + { IS31FL319X_PWM(0), 0x00},
> + { IS31FL319X_PWM(1), 0x00},
> + { IS31FL319X_PWM(2), 0x00},
> + { IS31FL319X_PWM(3), 0x00},
> + { IS31FL319X_PWM(4), 0x00},
> + { IS31FL319X_PWM(5), 0x00},
> + { IS31FL319X_PWM(6), 0x00},
> + { IS31FL319X_PWM(7), 0x00},
> + { IS31FL319X_PWM(8), 0x00},
> +};
> +
> +static struct regmap_config regmap_config = {
> + .reg_bits = 8,
> + .val_bits = 8,
> + .max_register = IS31FL319X_REG_CNT,
> + .cache_type = REGCACHE_FLAT,
> + .readable_reg = is31fl319x_readable_reg,
> + .volatile_reg = is31fl319x_volatile_reg,
> + .reg_defaults = is31fl319x_reg_defaults,
> + .num_reg_defaults = ARRAY_SIZE(is31fl319x_reg_defaults),
> +};
> +
> +static inline int is31fl319x_microamp_to_cs(struct device *dev, u32 microamp)
> +{ /* round down to nearest supported value (range check done by caller) */
> + u32 step = microamp / IS31FL319X_CURRENT_STEP;
> +
> + return ((IS31FL319X_CONFIG2_CS_STEP_REF - step) &
> + IS31FL319X_CONFIG2_CS_MASK) <<
> + IS31FL319X_CONFIG2_CS_SHIFT; /* CS encoding */
> +}
> +
> +static inline int is31fl319x_db_to_gain(u32 dezibel)
> +{ /* round down to nearest supported value (range check done by caller) */
> + return dezibel / IS31FL319X_AUDIO_GAIN_DB_STEP;
> +}
> +
> +static int is31fl319x_probe(struct i2c_client *client,
> + const struct i2c_device_id *id)
> +{
> + struct is31fl319x_chip *is31;
> + struct device *dev = &client->dev;
> + struct i2c_adapter *adapter = to_i2c_adapter(dev->parent);
> + int err;
> + int i = 0;
> + u32 aggregated_led_microamp = IS31FL319X_CURRENT_MAX;
> +
> + if (!i2c_check_functionality(adapter, I2C_FUNC_I2C))
> + return -EIO;
> +
> + is31 = devm_kzalloc(&client->dev, sizeof(*is31), GFP_KERNEL);
> + if (!is31)
> + return -ENOMEM;
> +
> + mutex_init(&is31->lock);
> +
> + err = is31fl319x_parse_dt(&client->dev, is31);
> + if (err)
> + goto free_mutex;
> +
> + is31->client = client;
> + is31->regmap = devm_regmap_init_i2c(client, &regmap_config);
> + if (IS_ERR(is31->regmap)) {
> + dev_err(&client->dev, "failed to allocate register map\n");
> + err = PTR_ERR(is31->regmap);
> + goto free_mutex;
> + }
> +
> + i2c_set_clientdata(client, is31);
> +
> + /* check for write-reply from chip (we can't read any registers) */
> + err = regmap_write(is31->regmap, IS31FL319X_RESET, 0x00);
> + if (err < 0) {
> + dev_err(&client->dev, "no response from chip write: err = %d\n",
> + err);
> + err = -EIO; /* does not answer */
> + goto free_mutex;
> + }
> +
> + /*
> + * Kernel conventions require per-LED led-max-microamp property.
> + * But the chip does not allow to limit individual LEDs.
> + * So we take minimum from all subnodes for safety of hardware.
> + */
> + for (i = 0; i < is31->cdef->num_leds; i++)
> + if (is31->leds[i].configured &&
> + is31->leds[i].max_microamp < aggregated_led_microamp)
> + aggregated_led_microamp = is31->leds[i].max_microamp;
> +
> + regmap_write(is31->regmap, IS31FL319X_CONFIG2,
> + is31fl319x_microamp_to_cs(dev, aggregated_led_microamp) |
> + is31fl319x_db_to_gain(is31->audio_gain_db));
> +
> + for (i = 0; i < is31->cdef->num_leds; i++) {
> + struct is31fl319x_led *led = &is31->leds[i];
> +
> + if (!led->configured)
> + continue;
> +
> + led->chip = is31;
> + led->cdev.brightness_set_blocking = is31fl319x_brightness_set;
> +
> + err = devm_led_classdev_register(&client->dev, &led->cdev);
> + if (err < 0)
> + goto free_mutex;
> + }
> +
> + return 0;
> +
> +free_mutex:
> + mutex_destroy(&is31->lock);
> + return err;
> +}
> +
> +static int is31fl319x_remove(struct i2c_client *client)
> +{
> + struct is31fl319x_chip *is31 = i2c_get_clientdata(client);
> +
> + mutex_destroy(&is31->lock);
> + return 0;
> +}
> +
> +/*
> + * i2c-core (and modalias) requires that id_table be properly filled,
> + * even though it is not used for DeviceTree based instantiation.
> + */
> +static const struct i2c_device_id is31fl319x_id[] = {
> + { "is31fl3190" },
> + { "is31fl3191" },
> + { "is31fl3193" },
> + { "is31fl3196" },
> + { "is31fl3199" },
> + { "sn3199" },
> + {},
> +};
> +MODULE_DEVICE_TABLE(i2c, is31fl319x_id);
> +
> +static struct i2c_driver is31fl319x_driver = {
> + .driver = {
> + .name = "leds-is31fl319x",
> + .of_match_table = of_match_ptr(of_is31fl319x_match),
> + },
> + .probe = is31fl319x_probe,
> + .remove = is31fl319x_remove,
> + .id_table = is31fl319x_id,
> +};
> +
> +module_i2c_driver(is31fl319x_driver);
> +
> +MODULE_AUTHOR("H. Nikolaus Schaller <hns@goldelico.com>");
> +MODULE_AUTHOR("Andrey Utkin <andrey_utkin@fastmail.com>");
> +MODULE_DESCRIPTION("IS31FL319X LED driver");
> +MODULE_LICENSE("GPL v2");
>

\
 
 \ /
  Last update: 2016-07-19 15:01    [W:1.057 / U:0.172 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site