lkml.org 
[lkml]   [2016]   [Jun]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH] mmc: dw_mmc: remove UBSAN warning in dw_mci_setup_bus()
Hi Jaehoon,

On 2016년 06월 09일 21:38, Jaehoon Chung wrote:
> Hi Seung-Woo,
>
> On 06/08/2016 01:07 PM, Seung-Woo Kim wrote:
>> This patch removes following UBSAN warnings in dw_mci_setup_bus().
>> The warnings are caused because of shift with more than 31 on 32
>> bit variable, so this patch fixes to shift only for less than 32.
>>
>> UBSAN: Undefined behaviour in drivers/mmc/host/dw_mmc.c:1102:14
>> shift exponent 250 is too large for 32-bit type 'unsigned int'
>> Call trace:
>> [<ffffff90080908a8>] dump_backtrace+0x0/0x380
>> [<ffffff9008090c3c>] show_stack+0x14/0x20
>> [<ffffff90087457b8>] dump_stack+0xe0/0x120
>> [<ffffff90087b1360>] ubsan_epilogue+0x18/0x68
>> [<ffffff90087b1a94>] __ubsan_handle_shift_out_of_bounds+0x18c/0x1bc
>> [<ffffff9008d89cb8>] dw_mci_setup_bus+0x3a0/0x438
>> [...]
>>
>> UBSAN: Undefined behaviour in drivers/mmc/host/dw_mmc.c:1132:27
>> shift exponent 250 is too large for 32-bit type 'unsigned int'
>> Call trace:
>> [<ffffff90080908a8>] dump_backtrace+0x0/0x380
>> [<ffffff9008090c3c>] show_stack+0x14/0x20
>> [<ffffff90087457b8>] dump_stack+0xe0/0x120
>> [<ffffff90087b1360>] ubsan_epilogue+0x18/0x68
>> [<ffffff90087b1a94>] __ubsan_handle_shift_out_of_bounds+0x18c/0x1bc
>> [<ffffff9008d89c9c>] dw_mci_setup_bus+0x384/0x438
>
> The below message can be discarded.

You are right, like above message, below part can be replaced as [...].

>
>> [<ffffff9008d89ed4>] dw_mci_set_ios+0x184/0x798
>> [<ffffff9008d550ac>] mmc_power_up+0x11c/0x260
>> [<ffffff9008d56b78>] mmc_start_host+0x88/0x100
>> [<ffffff9008d583f4>] mmc_add_host+0x6c/0x128
>> [<ffffff9008d88f90>] dw_mci_probe+0x1088/0x1750
>> [<ffffff9008d8caa8>] dw_mci_pltfm_register+0x108/0x178
>> [<ffffff9008d8dae4>] dw_mci_exynos_probe+0x4c/0x88
>> [<ffffff9008a03838>] platform_drv_probe+0x78/0x180
>> [<ffffff90089fe9fc>] driver_probe_device+0x144/0x460
>> [<ffffff90089fee0c>] __driver_attach+0xf4/0x140
>> [<ffffff90089fad98>] bus_for_each_dev+0xf0/0x160
>> [<ffffff90089fdc9c>] driver_attach+0x34/0x58
>> [<ffffff90089fd3e0>] bus_add_driver+0x2c0/0x398
>> [<ffffff9008a00924>] driver_register+0xbc/0x1e0
>> [<ffffff9008a02a94>] __platform_driver_register+0x84/0xa8
>> [<ffffff9009dd5730>] dw_mci_exynos_pltfm_driver_init+0x18/0x20
>> [<ffffff9008082df8>] do_one_initcall+0xa0/0x2c8
>> [<ffffff9009d81780>] kernel_init_freeable+0x52c/0x5dc
>> [<ffffff9009519844>] kernel_init+0x1c/0xf8
>> [<ffffff9008086e10>] ret_from_fork+0x10/0x40
>>
>> Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
>> ---
>> drivers/mmc/host/dw_mmc.c | 5 +++--
>> 1 files changed, 3 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
>> index 2cc6123..dff045e 100644
>> --- a/drivers/mmc/host/dw_mmc.c
>> +++ b/drivers/mmc/host/dw_mmc.c
>> @@ -1099,7 +1099,8 @@ static void dw_mci_setup_bus(struct dw_mci_slot *slot, bool force_clkinit)
>>
>> div = (host->bus_hz != clock) ? DIV_ROUND_UP(div, 2) : 0;
>>
>> - if ((clock << div) != slot->__clk_old || force_clkinit)
>> + if (((div < 32) ? (clock << div) : 0) != slot->__clk_old ||
>
> Well, we don't expect that clock is 0.
> if clock is 0, it should be passed to " if (!clock)"..
>
> During initializing card, clock is 400KHz or less..I understood what you want to fix.
> But I taught this is not correct.

It seems slot->__clk_old is not really clock but a kind of value to
store both clock and div in one variable. And at least, my compiler
calculates right shift with more than 32 as 0. I am not sure there is
other proper value for the case.

By the way, in my test environment, clock is calculated as like
following steps:
mmc_host mmc0: Bus speed (slot 0) = 200000000Hz (slot req 400000Hz,
actual 400000HZ div = 250)
mmc_host mmc0: Bus speed (slot 0) = 200000000Hz (slot req 200000000Hz,
actual 200000000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 200000000Hz (slot req 52000000Hz,
actual 50000000HZ div = 2)
mmc_host mmc0: Bus speed (slot 0) = 400000000Hz (slot req 52000000Hz,
actual 50000000HZ div = 4)
mmc_host mmc0: Bus speed (slot 0) = 400000000Hz (slot req 200000000Hz,
actual 200000000HZ div = 1)

and only the first case is reported as the warning. If you let me know
any proper value, then I will fix with the value.

Thanks,
- Seung-Woo Kim


>
>
>> + force_clkinit)
>> dev_info(&slot->mmc->class_dev,
>> "Bus speed (slot %d) = %dHz (slot req %dHz, actual %dHZ div = %d)\n",
>> slot->id, host->bus_hz, clock,
>> @@ -1129,7 +1130,7 @@ static void dw_mci_setup_bus(struct dw_mci_slot *slot, bool force_clkinit)
>> mci_send_cmd(slot, sdmmc_cmd_bits, 0);
>>
>> /* keep the clock with reflecting clock dividor */
>> - slot->__clk_old = clock << div;
>> + slot->__clk_old = (div < 32) ? (clock << div) : 0;
>
> Also, clock is not 0..
>
>
> Best Regards,
> Jaehoon Chung
>
>> }
>>
>> host->current_speed = clock;
>>
>
>
>

--
Seung-Woo Kim
Samsung Software R&D Center
--

\
 
 \ /
  Last update: 2016-06-10 04:01    [W:0.132 / U:0.696 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site