lkml.org 
[lkml]   [2016]   [Jun]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v4 2/2] [media] atmel-isc: DT binding for Image Sensor Controller driver
On Tue, Jun 07, 2016 at 03:11:53PM +0800, Songjun Wu wrote:
> DT binding documentation for ISC driver.
>
> Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
> ---
>
> Changes in v4:
> - Remove the isc clock nodes.
>
> Changes in v3:
> - Remove the 'atmel,sensor-preferred'.
> - Modify the isc clock node according to the Rob's remarks.
>
> Changes in v2:
> - Remove the unit address of the endpoint.
> - Add the unit address to the clock node.
> - Avoid using underscores in node names.
> - Drop the "0x" in the unit address of the i2c node.
> - Modify the description of 'atmel,sensor-preferred'.
> - Add the description for the ISC internal clock.
>
> .../devicetree/bindings/media/atmel-isc.txt | 69 ++++++++++++++++++++++
> 1 file changed, 69 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/atmel-isc.txt

Almost there...

> diff --git a/Documentation/devicetree/bindings/media/atmel-isc.txt b/Documentation/devicetree/bindings/media/atmel-isc.txt
> new file mode 100644
> index 0000000..3f83524
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/atmel-isc.txt
> @@ -0,0 +1,69 @@
> +Atmel Image Sensor Controller (ISC)
> +----------------------------------------------
> +
> +Required properties for ISC:
> +- compatible
> + Must be "atmel,sama5d2-isc".
> +- reg
> + Physical base address and length of the registers set for the device.
> +- interrupts
> + Should contain IRQ line for the ISC.
> +- clocks
> + List of clock specifiers, corresponding to entries in
> + the clock-names property;
> + Please refer to clock-bindings.txt.
> +- clock-names
> + Required elements: "hclock".
> +- #clock-cells
> + Should be 0.
> +- clock-output-names
> + Should contain the name of the clock driving the sensor master clock.
> +- pinctrl-names, pinctrl-0
> + Please refer to pinctrl-bindings.txt.

Required, but not in your example.

> +
> +
> +ISC supports a single port node with parallel bus. It should contain one
> +'port' child node with child 'endpoint' node. Please refer to the bindings
> +defined in Documentation/devicetree/bindings/media/video-interfaces.txt.
> +
> +Example:
> +isc: isc@f0008000 {
> + compatible = "atmel,sama5d2-isc";
> + reg = <0xf0008000 0x4000>;
> + interrupts = <46 IRQ_TYPE_LEVEL_HIGH 5>;
> + clocks = <&isc_clk>, <&iscck>, <&isc_gclk>;
> + clock-names = "hclock";
> + #clock-cells = <0>;
> + clock-output-names = "isc-mck";
> +
> + port {
> + #address-cells = <1>;
> + #size-cells = <0>;

These 2 you can drop.

> +
> + isc_0: endpoint {
> + remote-endpoint = <&ov7740_0>;
> + hsync-active = <1>;
> + vsync-active = <0>;
> + pclk-sample = <1>;
> + };
> + };
> +
> +
> +};
> +
> +i2c1: i2c@fc028000 {
> + ov7740: camera@21 {
> + compatible = "ovti,ov7740";

Fix the indentation.

> + reg = <0x21>;
> +
> + clocks = <&isc>;
> + clock-names = "xvclk";
> + assigned-clocks = <&isc>;
> + assigned-clock-rates = <24000000>;
> +
> + port {
> + ov7740_0: endpoint {
> + remote-endpoint = <&isc_0>;
> + };
> + };
> +};
> --
> 2.7.4
>

\
 
 \ /
  Last update: 2016-06-08 22:21    [W:0.136 / U:0.016 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site