lkml.org 
[lkml]   [2016]   [Jun]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 3/6] ASoC: sgtl5000: Initialize CHIP_ANA_POWER to power-on defaults
Date
From: Eric Nelson <eric@nelint.com>

Initialize CHIP_ANA_POWER to match power on defaults, which disables
ADC, DAC, and charge pumps.

In the process, remove references to the following register/bitfields
from the sgtl5000_set_power_regs routine:
CHIP_ANA_POWER/LINREG_SIMPLE_POWERUP and
CHIP_LINREG_CTRL/LINREG_VDD_MASK

And remove CHIP_ANA_POWER and CHIP_LINREG_CTRL from the set of default
registers so they don't get clobbered by sgtl5000_fill_defaults().

Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
---
sound/soc/codecs/sgtl5000.c | 56 +++++++++++++++++----------------------------
sound/soc/codecs/sgtl5000.h | 1 +
2 files changed, 22 insertions(+), 35 deletions(-)

diff --git a/sound/soc/codecs/sgtl5000.c b/sound/soc/codecs/sgtl5000.c
index fd8cfec..59eee45 100644
--- a/sound/soc/codecs/sgtl5000.c
+++ b/sound/soc/codecs/sgtl5000.c
@@ -47,12 +47,10 @@ static const struct reg_default sgtl5000_reg_defaults[] = {
{ SGTL5000_CHIP_ANA_ADC_CTRL, 0x0000 },
{ SGTL5000_CHIP_ANA_HP_CTRL, 0x1818 },
{ SGTL5000_CHIP_ANA_CTRL, 0x0111 },
- { SGTL5000_CHIP_LINREG_CTRL, 0x0000 },
{ SGTL5000_CHIP_REF_CTRL, 0x0000 },
{ SGTL5000_CHIP_MIC_CTRL, 0x0000 },
{ SGTL5000_CHIP_LINE_OUT_CTRL, 0x0000 },
{ SGTL5000_CHIP_LINE_OUT_VOL, 0x0404 },
- { SGTL5000_CHIP_ANA_POWER, 0x7060 },
{ SGTL5000_CHIP_PLL_CTRL, 0x5000 },
{ SGTL5000_CHIP_CLK_TOP_CTRL, 0x0000 },
{ SGTL5000_CHIP_ANA_STATUS, 0x0000 },
@@ -93,6 +91,7 @@ static const char *supply_names[SGTL5000_SUPPLY_NUM] = {
};

#define LDO_VOLTAGE 1200000
+#define LINREG_VDDD ((1600 - LDO_VOLTAGE / 1000) / 50)

enum sgtl5000_micbias_resistor {
SGTL5000_MICBIAS_OFF = 0,
@@ -1003,25 +1002,6 @@ static int sgtl5000_set_power_regs(struct snd_soc_codec *codec)

snd_soc_write(codec, SGTL5000_CHIP_ANA_POWER, ana_pwr);

- /* set voltage to register */
- snd_soc_update_bits(codec, SGTL5000_CHIP_LINREG_CTRL,
- SGTL5000_LINREG_VDDD_MASK, 0x8);
-
- /*
- * if vddd linear reg has been enabled,
- * simple digital supply should be clear to get
- * proper VDDD voltage.
- */
- if (ana_pwr & SGTL5000_LINEREG_D_POWERUP)
- snd_soc_update_bits(codec, SGTL5000_CHIP_ANA_POWER,
- SGTL5000_LINREG_SIMPLE_POWERUP,
- 0);
- else
- snd_soc_update_bits(codec, SGTL5000_CHIP_ANA_POWER,
- SGTL5000_LINREG_SIMPLE_POWERUP |
- SGTL5000_STARTUP_POWERUP,
- 0);
-
/*
* set ADC/DAC VAG to vdda / 2,
* should stay in range (0.8v, 1.575v)
@@ -1243,6 +1223,7 @@ static int sgtl5000_i2c_probe(struct i2c_client *client,
int ret, reg, rev;
struct device_node *np = client->dev.of_node;
u32 value;
+ u16 ana_pwr;

sgtl5000 = devm_kzalloc(&client->dev, sizeof(*sgtl5000), GFP_KERNEL);
if (!sgtl5000)
@@ -1300,29 +1281,34 @@ static int sgtl5000_i2c_probe(struct i2c_client *client,
sgtl5000->revision = rev;

/* Follow section 2.2.1.1 of AN3663 */
+ ana_pwr = SGTL5000_ANA_POWER_DEFAULT;
if (sgtl5000->num_supplies <= VDDD) {
/* internal VDDD at 1.2V */
- regmap_update_bits(sgtl5000->regmap,
- SGTL5000_CHIP_LINREG_CTRL,
- SGTL5000_LINREG_VDDD_MASK, 8);
- regmap_update_bits(sgtl5000->regmap,
- SGTL5000_CHIP_ANA_POWER,
- SGTL5000_LINEREG_D_POWERUP
- | SGTL5000_LINREG_SIMPLE_POWERUP,
- SGTL5000_LINEREG_D_POWERUP);
- dev_info(&client->dev, "Using internal LDO instead of VDDD: check ER1\n");
+ ret = regmap_update_bits(sgtl5000->regmap,
+ SGTL5000_CHIP_LINREG_CTRL,
+ SGTL5000_LINREG_VDDD_MASK,
+ LINREG_VDDD);
+ if (ret)
+ dev_err(&client->dev,
+ "Error %d setting LINREG_VDDD\n", ret);
+
+ ana_pwr |= SGTL5000_LINEREG_D_POWERUP;
+ dev_info(&client->dev,
+ "Using internal LDO instead of VDDD: check ER1\n");
} else {
/* using external LDO for VDDD
* Clear startup powerup and simple powerup
* bits to save power
*/
- regmap_update_bits(sgtl5000->regmap,
- SGTL5000_CHIP_ANA_POWER,
- SGTL5000_STARTUP_POWERUP
- | SGTL5000_LINREG_SIMPLE_POWERUP,
- 0);
+ ana_pwr &= ~(SGTL5000_STARTUP_POWERUP
+ | SGTL5000_LINREG_SIMPLE_POWERUP);
dev_dbg(&client->dev, "Using external VDDD\n");
}
+ ret = regmap_write(sgtl5000->regmap, SGTL5000_CHIP_ANA_POWER, ana_pwr);
+ if (ret)
+ dev_err(&client->dev,
+ "Error %d setting CHIP_ANA_POWER to %04x\n",
+ ret, ana_pwr);

if (np) {
if (!of_property_read_u32(np,
diff --git a/sound/soc/codecs/sgtl5000.h b/sound/soc/codecs/sgtl5000.h
index 1c317de..1be8237 100644
--- a/sound/soc/codecs/sgtl5000.h
+++ b/sound/soc/codecs/sgtl5000.h
@@ -325,6 +325,7 @@
/*
* SGTL5000_CHIP_ANA_POWER
*/
+#define SGTL5000_ANA_POWER_DEFAULT 0x7060
#define SGTL5000_DAC_STEREO 0x4000
#define SGTL5000_LINREG_SIMPLE_POWERUP 0x2000
#define SGTL5000_STARTUP_POWERUP 0x1000
--
2.8.3
\
 
 \ /
  Last update: 2016-06-07 01:41    [W:1.213 / U:0.108 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site