lkml.org 
[lkml]   [2016]   [Jun]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [linux-sunxi] [PATCH v2 14/14] ARM: dts: sun8i: Enable DVFS on Orange Pi One
On 30 June 2016 at 17:16, Michal Suchanek <hramrach@gmail.com> wrote:
> On 30 June 2016 at 16:19, Ondřej Jirman <megous@megous.com> wrote:
>> Hello,
>>
>> On 30.6.2016 13:13, Michal Suchanek wrote:
>>> Hello,
>>>
>>> On 25 June 2016 at 05:45, <megous@megous.com> wrote:
>>>> From: Ondrej Jirman <megous@megous.com>
>>>>
>>>> Use Xulong Orange Pi One GPIO based regulator for
>>>> passive cooling and thermal management.
>>>>
>>>> Signed-off-by: Ondrej Jirman <megous@megous.com>
>>>> ---
>>>> arch/arm/boot/dts/sun8i-h3-orangepi-one.dts | 39 +++++++++++++++++++++++++++++
>>>> 1 file changed, 39 insertions(+)
>>>>
>>>> diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
>>>> index b1bd6b0..a38d871 100644
>>>> --- a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
>>>> +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
>>>> @@ -109,6 +109,45 @@
>>>> };
>>>> };
>>>>
>>>> +&cpu0 {
>>>> + operating-points = <
>>>> + /* kHz uV */
>>>> + 1296000 1300000
>>>> + 1200000 1300000
>>>
>>> First problem is that the board boots at 1008000 which is not listed
>>> and the kernel complains.
>>>
>>> Second problem is that the board locks up during boot with this enabled.
>>>
>>> Do you have some suggestion for alternate configuration to test?
>>
>> Just to verify, did you test with the entire series applied? (especially
>> the PLL1 clk application changes)
>
> Yes, I applied the whole series.
>
>>
>> You may try dropping the highest operating point, it's probably overly
>> optimistic for Orange Pi One.
>>
>> Is the power supply/cable you're using hard enough?
>
> I use a 7 port hub to power the board. It worked with some other small
> devboards.
>
> The cable is some random Chinese USB to power jack adaptor with an
> extra adaptor to fit the Pi socket. It looks ok but I did not test
> this particular combination thoroughly.
>
>>
>> Where during the boot process does it lock up?
>
> Usually sometime around enabling cpufreq before getty starts.
> Different runs and settings give slightly different results. In
> particular adding the 1008000 point seems to make it go further.
>
> Removing all traces of the regulator, cpufreq and thermal I can boot
> pretty much 100% to login prompt.
>
> I don't think the difference between 1GHz and 1.3GHz frequency on the
> core would put much additional stress on the supply but I can try with
> 35W PSU and some alternative cabling to be sure.
>
> I did some more tests and it seems 1008000@1.1V is fine but switching
> to 1.3V crashes the board. Even with only the first 1.3V state. Maybe
> there is need for some delay somewhere for the regulator to get
> stable?
>

Hm, the AW table shows 1008000@1.3V as supported state and it indeed
works. So the voltage switching works or does nothing. Can I measure
the regulator output somewhere? Clocking the chip higher does not
work.

I will try with another PSU later.

Thanks

Michal

\
 
 \ /
  Last update: 2016-06-30 18:41    [W:0.053 / U:0.764 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site