lkml.org 
[lkml]   [2016]   [Jun]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [Y2038] [PATCH] crypto: use timespec64 for jent_get_nstime
Date
Am Dienstag, 21. Juni 2016, 09:47:23 schrieb John Stultz:

Hi John,

> On Tue, Jun 21, 2016 at 9:34 AM, Stephan Mueller <smueller@chronox.de>
wrote:
> > Am Dienstag, 21. Juni 2016, 09:22:31 schrieb John Stultz:
> >
> > Hi John,
> >
> >> On Tue, Jun 21, 2016 at 1:32 AM, Arnd Bergmann <arnd@arndb.de> wrote:
> >> > On Tuesday, June 21, 2016 8:20:10 AM CEST Stephan Mueller wrote:
> >> >> Am Freitag, 17. Juni 2016, 17:59:41 schrieb Arnd Bergmann:
> >> > Compared to the previous __getnstimeofday(), the difference is
> >> >
> >> > - using "monotonic" timebase instead of "real", so the zero time
> >> >
> >> > is when the system booted rather than Jan 1 1970
> >>
> >> I haven't looked at the details of the calling code, but I'd worry for
> >> crypto uses, especially if its being used for entropy collection,
> >> using the monotonic clock instead of the realtime clock might be
> >> problematic.
> >
> > Funnily it does not seem like that. All tests that I have conducted show
> > that monotonic clocks behave equally as realtime clocks, because the
> > uncertainty lies in the execution time of a set of instructions. All we
> > need to do is to measure it with a timer that has a resolution that
> > allows detecting these variations.
>
> Ok. If you're only using it for interval measurements, then either way
> shouldn't matter. I just wanted to make sure the entropy wasn't coming
> from the actual time.
>
> >> > - "raw" means we don't honor updates for the rate based on ntp,
> >> >
> >> > which is probably better as the ntp state might be observable
> >> > over the net (it probably doesn't matter, but it can't hurt)
> >>
> >> So... this feels like a very vague explanation, and the lack of
> >> frequency correction here probably need a really good comment. Keeping
> >> multiple time domains is usually asking for trouble, but we added the
> >> MONOTONIC_RAW clock to address a few cases where people really wanted
> >> an abstract hardware counter, which was unaffected by frequency
> >> corrections. I'd really make sure its clear why this is what you want
> >> vs the standard system time domain so we don't run into problems
> >> understanding it later.
> >
> > Perfect, that is what I would be interested in.
>
> But documenting *why* clearly is the thing I'd very strongly suggest.
> If we need to make some slight semantic change for whatever reason, I
> don't want folks worried "we can't do that because the crypto code is
> using it for voodoo".

I hope my explanation is sufficient to not count as voodoo: I only need an
interval measurement capability which has a sufficient high resolution similar
or better than RDTSC on x86.
>
> >> > - "fast" means that in very rare cases, the time might appear
> >> >
> >> > to go backwards (it probably can't happen here because you are not
> >> > called in an NMI).
> >>
> >> "fast" really means "safe-for-nmi wrt to locking". The tradeoff being
> >> that when frequency adjustments occur, and if your code is delayed,
> >> you might see time go backwards by a small amount. This allows
> >
> > My code would not see that as an issue.
> >
> >> tracing/sched code (or other code called from NMI) to not have to
> >> duplicate the timekeeping infrastructure.
> >>
> >> I think without a much better explanation, using the "fast" method
> >> isn't really warranted here.
> >
> > Thanks a lot. With that, I would think that the proposed
> > ktime_get_raw_fast_ns is good for use, which is supported with testing on
> > my system.
>
> So.. again, I'd avoid using the "fast" accessor unless there is a
> clear need or obvious benefit. Which should be documented.

So, you suggest ktime_get_raw_ns? If yes, let me test that for one use case.

Thanks
Stephan

\
 
 \ /
  Last update: 2016-06-21 19:21    [W:0.048 / U:0.352 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site