lkml.org 
[lkml]   [2016]   [Jun]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
SubjectRE: [PATCH] Input: elan_i2c - +200 ms delay before setting to ABS mode
Date
Hi Dmitry,

The modification from Chris is a special case.
Because the Touchpad FW is a little different from normal one, It cause
problem in Asus's OBE test.

That's why Elan's driver use work-around to solve the problem. It's not
tested by other touchpad.

Let me discuss with internal FW team to confirm the harmless of the patch.

B.R KT
-----Original Message-----
From: Dmitry Torokhov [mailto:dmitry.torokhov@gmail.com]
Sent: Tuesday, June 21, 2016 1:43 AM
To: Chris Chiu; kt.liao@emc.com.tw
Cc: Charlie Mooney; Michele Curti; Krzysztof Kozlowski; Benson Leung;
linux-input@vger.kernel.org; linux-kernel@vger.kernel.org;
linux@endlessm.com
Subject: Re: [PATCH] Input: elan_i2c - +200 ms delay before setting to ABS
mode

On Tue, Jun 07, 2016 at 09:34:09PM +0800, Chris Chiu wrote:
> When performing a warm reboot from a system which does not correctly
> support ELAN I2C touchpads, the touchpad will sometimes enter standard
> mouse mode, cursor then never respond to touchpad event, and making
> the driver discard the HID reports and flood dmesg with following
> error messages.
> "elan_i2c i2c-ELAN1000:00: invalid report id data (1)"
>
> This change is from ELAN's correction. It needs 200ms delay before
> set_mode() so that the mode setting will correctly take effect.

KT, is this feasible?

>
> Signed-off-by: Chris Chiu <chiu@endlessm.com>
> ---
> drivers/input/mouse/elan_i2c_core.c | 12 +++++++-----
> 1 file changed, 7 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/input/mouse/elan_i2c_core.c
> b/drivers/input/mouse/elan_i2c_core.c
> index 2f58985..95080f9 100644
> --- a/drivers/input/mouse/elan_i2c_core.c
> +++ b/drivers/input/mouse/elan_i2c_core.c
> @@ -210,18 +210,20 @@ static int __elan_initialize(struct elan_tp_data
*data)
> return error;
> }
>
> - data->mode |= ETP_ENABLE_ABS;
> - error = data->ops->set_mode(client, data->mode);
> + error = data->ops->sleep_control(client, false);
> if (error) {
> dev_err(&client->dev,
> - "failed to switch to absolute mode: %d\n", error);
> + "failed to wake device up: %d\n", error);
> return error;
> }
>
> - error = data->ops->sleep_control(client, false);
> + msleep(200);
> +
> + data->mode |= ETP_ENABLE_ABS;
> + error = data->ops->set_mode(client, data->mode);
> if (error) {
> dev_err(&client->dev,
> - "failed to wake device up: %d\n", error);
> + "failed to switch to absolute mode: %d\n", error);
> return error;
> }
>
> --
> 2.1.4
>

Thanks.

--
Dmitry

\
 
 \ /
  Last update: 2016-06-21 04:01    [W:0.076 / U:2.608 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site