lkml.org 
[lkml]   [2016]   [Jun]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 2/3] Documentation: add DT bindings for ARM SCPI power domains
Date
The System Control Processor (SCP) provides peripheral devices with
power domains that can be enabled and disabled viathe System Control
and Power Interface (SCPI) Message Protocol. Add bindings to allow
probing of these device power domians.

Cc: Rob Herring <robh+dt@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
---
Documentation/devicetree/bindings/arm/arm,scpi.txt | 34 ++++++++++++++++++++++
1 file changed, 34 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/arm,scpi.txt b/Documentation/devicetree/bindings/arm/arm,scpi.txt
index 313dabdc14f9..faa4b44572e3 100644
--- a/Documentation/devicetree/bindings/arm/arm,scpi.txt
+++ b/Documentation/devicetree/bindings/arm/arm,scpi.txt
@@ -87,10 +87,33 @@ SCPI provides an API to access the various sensors on the SoC.
implementation for the IDs to use. For Juno
R0 and Juno R1 refer to [3].

+Power domain bindings for the power domains based on SCPI Message Protocol
+------------------------------------------------------------
+
+This binding uses the generic power domain binding[4].
+
+PM domain providers
+===================
+
+Required properties:
+ - #power-domain-cells : Should be 1. Contains the device or the power
+ domain ID value used by SCPI commands.
+ - num-domains: Total number of power domains provided by SCPI. This is
+ needed as the SCPI message protocol lacks a mechanism to
+ query this information at runtime.
+
+PM domain consumers
+===================
+
+Required properties:
+ - power-domains : A phandle and PM domain specifier as defined by bindings of
+ the power controller specified by phandle.
+
[0] http://infocenter.arm.com/help/topic/com.arm.doc.dui0922b/index.html
[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
[2] Documentation/devicetree/bindings/thermal/thermal.txt
[3] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dui0922b/apas03s22.html
+[4] Documentation/devicetree/bindings/power/power_domain.txt

Example:

@@ -144,6 +167,12 @@ scpi_protocol: scpi@2e000000 {
compatible = "arm,scpi-sensors";
#thermal-sensor-cells = <1>;
};
+
+ scpi_devpd: scpi-power-domains {
+ compatible = "arm,scpi-power-domains";
+ num-domains = <2>;
+ #power-domain-cells = <1>;
+ };
};

cpu@0 {
@@ -156,6 +185,7 @@ hdlcd@7ff60000 {
...
reg = <0 0x7ff60000 0 0x1000>;
clocks = <&scpi_clk 4>;
+ power-domains = <&scpi_devpd 1>;
};

thermal-zones {
@@ -186,3 +216,7 @@ The thermal-sensors property in the soc_thermal node uses the
temperature sensor provided by SCP firmware to setup a thermal
zone. The ID "3" is the sensor identifier for the temperature sensor
as used by the firmware.
+
+The num-domains property in scpi-power-domains domain specifies that
+SCPI provides 2 power domains. The hdlcd node uses the power domain with
+domain ID 1.
--
2.7.4
\
 
 \ /
  Last update: 2016-06-16 13:21    [W:0.219 / U:0.916 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site