lkml.org 
[lkml]   [2016]   [May]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] video: fbdev: mxsfb: fix pixelclock polarity
Hi Shawn,

On 2016-01-25 17:29, Stefan Agner wrote:
> The PIXDATA flags of the display_flags enum are controller centric,
> e.g. NEGEDGE means the controller shall drive the data signals on
> pixelclocks negative edge. However, the drivers flag is display
> centric: Sample the data on negative (falling) edge.
>
> Therefore, change the if statement to check for the POSEDGE flag
> (which is typically not set):
> Drive on positive edge => sample on negative edge

Any comment on that patch?

--
Stefan


>
> Signed-off-by: Stefan Agner <stefan@agner.ch>
> ---
> Hi all
>
> Shawn, I would like to have at least your Ack on this before merge.
>
> It seems that this has been wrong since the driver is able to use
> the timings from the device tree, introduced with 669406534b4a
> ("video: mxsfb: get display timings from device tree").
>
> Not sure how many device trees actually specify the wrong pixel clock
> polarity due to that. At least the initial flag convertion from the
> old platform data structures done with 0d9f8217db15 ("ARM: mxs: move
> display timing configurations into device tree") seems to be affected
> and would need to be changed accordingly...
>
> Not sure how we should handle this, maybe just invert all
> pixelclk-active properties where the mxsfb driver is in use...?
>
> --
> Stefan
>
> drivers/video/fbdev/mxsfb.c | 13 +++++++++++--
> 1 file changed, 11 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/video/fbdev/mxsfb.c b/drivers/video/fbdev/mxsfb.c
> index 4e6608c..38898a9 100644
> --- a/drivers/video/fbdev/mxsfb.c
> +++ b/drivers/video/fbdev/mxsfb.c
> @@ -150,7 +150,7 @@
> #define STMLCDIF_24BIT 3 /** pixel data bus to the display is of 24
> bit width */
>
> #define MXSFB_SYNC_DATA_ENABLE_HIGH_ACT (1 << 6)
> -#define MXSFB_SYNC_DOTCLK_FALLING_ACT (1 << 7) /* negtive edge sampling */
> +#define MXSFB_SYNC_DOTCLK_FALLING_ACT (1 << 7) /* negative edge sampling */
>
> enum mxsfb_devtype {
> MXSFB_V3,
> @@ -788,7 +788,16 @@ static int mxsfb_init_fbinfo_dt(struct mxsfb_info *host,
>
> if (vm.flags & DISPLAY_FLAGS_DE_HIGH)
> host->sync |= MXSFB_SYNC_DATA_ENABLE_HIGH_ACT;
> - if (vm.flags & DISPLAY_FLAGS_PIXDATA_NEGEDGE)
> +
> + /*
> + * The PIXDATA flags of the display_flags enum are controller
> + * centric, e.g. NEGEDGE means drive data on negative edge.
> + * However, the drivers flag is display centric: Sample the
> + * data on negative (falling) edge. Therefore, check for the
> + * POSEDGE flag:
> + * drive on positive edge => sample on negative edge
> + */
> + if (vm.flags & DISPLAY_FLAGS_PIXDATA_POSEDGE)
> host->sync |= MXSFB_SYNC_DOTCLK_FALLING_ACT;
>
> put_display_node:

\
 
 \ /
  Last update: 2016-05-06 23:01    [W:0.078 / U:0.256 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site