lkml.org 
[lkml]   [2016]   [May]   [31]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [RFC PATCH v2] ACPICA / Hardware: Fix old register check in acpi_hw_get_access_bit_width()
Date
Hi, Boris and Mike

Please help to validate if this version can also fix your issues.
After enumerating the possible cases, I realized that the address check might not be necessary.
But we need a max_bit_width check in this function to make it prepared for a future usage in acpi_read()/acpi_write().
Thanks in advance.

Best regards
-Lv

> From: Zheng, Lv
> Subject: [RFC PATCH v2] ACPICA / Hardware: Fix old register check in
> acpi_hw_get_access_bit_width()
>
> The address check in acpi_hw_get_access_bit_width() should be byte
> width
> based, not bit width based. This patch fixes this mistake.
>
> For those who want to review acpi_hw_access_bit_width(), here is the
> concerns and the design details of the function:
>
> It is supposed that the GAS Address field should be aligned to the byte
> width indicated by the GAS AccessSize field. Similarly, for the old non
> GAS register, it is supposed that its Address should be aligned to its
> Length.
> For the "AccessSize = 0 (meaning ANY)" case, we try to return the
> maximum
> instruction width (64 for MMIO or 32 for PIO) or the user expected access
> bit width (64 for acpi_read()/acpi_write() or 32 for acpi_hw_read()/
> acpi_hw_write()) for futher operation and it is supposed that the GAS
> Address field should always be aligned to the maximum expected access
> bit
> width (otherwise it can't be ANY).
>
> The problem is in acpi_tb_init_generic_address(), where the non GAS
> register's Length is converted into the GAS BitWidth field, its Address is
> converted into the GAS Address field, and the GAS AccessSize field is left
> 0 but most of the register actually cannot be accessed using "ANY"
> accesses.
>
> As a conclusion, when AccessSize = 0 (ANY), the Address should either be
> aligned to the BitWidth (wrong conversion) or aligned to 32 (PIO) or 64
> (MMIO). Since BitWidth for the wrong conversion is 8,16,32, the Address
> of the real GAS should always be aligned to 8,16,32, the address alignment
> check is not necessary. But we in fact could enhance the check for a future
> case where max_bit_width could be 64 for a PIO access issued from
> acpi_read()/acpi_write().
>
> Fixes: b314a172ee96 ("ACPICA: Hardware: Add optimized access bit width
> support")
> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
> Cc: Mike Marshall <hubcap@omnibond.com>
> Suggested-by: Jan Beulich <jbeulich@suse.com>
> Signed-off-by: Lv Zheng <lv.zheng@intel.com>
> ---
> drivers/acpi/acpica/hwregs.c | 16 +++++++---------
> 1 file changed, 7 insertions(+), 9 deletions(-)
>
> diff --git a/drivers/acpi/acpica/hwregs.c b/drivers/acpi/acpica/hwregs.c
> index 0f18dbc..0553c0b 100644
> --- a/drivers/acpi/acpica/hwregs.c
> +++ b/drivers/acpi/acpica/hwregs.c
> @@ -86,24 +86,22 @@ acpi_hw_get_access_bit_width(struct
> acpi_generic_address *reg, u8 max_bit_width)
> u64 address;
>
> if (!reg->access_width) {
> + if (reg->space_id == ACPI_ADR_SPACE_SYSTEM_IO) {
> + max_bit_width = 32;
> + }
> /*
> * Detect old register descriptors where only the bit_width
> field
> * makes senses. The target address is copied to handle
> possible
> * alignment issues.
> */
> ACPI_MOVE_64_TO_64(&address, &reg->address);
> - if (!reg->bit_offset && reg->bit_width &&
> + if (reg->bit_width < max_bit_width &&
> + !reg->bit_offset && reg->bit_width &&
> ACPI_IS_POWER_OF_TWO(reg->bit_width) &&
> - ACPI_IS_ALIGNED(reg->bit_width, 8) &&
> - ACPI_IS_ALIGNED(address, reg->bit_width)) {
> + ACPI_IS_ALIGNED(reg->bit_width, 8)) {
> return (reg->bit_width);
> - } else {
> - if (reg->space_id == ACPI_ADR_SPACE_SYSTEM_IO)
> {
> - return (32);
> - } else {
> - return (max_bit_width);
> - }
> }
> + return (max_bit_width);
> } else {
> return (1 << (reg->access_width + 2));
> }
> --
> 1.7.10

\
 
 \ /
  Last update: 2016-05-31 09:21    [W:0.125 / U:0.176 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site