lkml.org 
[lkml]   [2016]   [May]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [RESEND PATCH] mmc: sdhci: fix wakeup configuration
On Fri, May 13, 2016 at 02:37:21PM +0300, Adrian Hunter wrote:
> + cc some Marvell people because they added this code
>
> On 13/05/16 12:27, Ludovic Desroches wrote:
> > Activating wakeup event is not enough to get a wakeup signal. The
> > corresponding events have to be enabled in the Interrupt Status Enable
> > Register too.
>
> That seems to follow the specification. Did you find that you actually
> needed this change to get it to work?
>

Yes, I din't wake up on card event without this patch.

> >
> > Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
> > ---
> > Hi,
> >
> > I just updated sdhci_enable_irq_wakeups() not sdhci_disable_irq_wakeups()
> > because I don't think it is necessary to configure SDHCI_INT_ENABLE at this
> > step, it will be done with sdhci_init() or sdhci_enable_card_detection().
>
> OK, but that should be in the commit message and commented in the code too.

I'll add it.

>
> >
> > While I was writing this patch, several questions came to my mind:
> > - Is the naming correct? wakeup signal is not an irq. 'enable_irq_wakeups' can
> > be a bit confusing.
>
> I don't support renaming things unless the names are really really bad.
> These names are OK.
>
> > - If we want to wakeup from irq, we may have to set SDHCI_INT_ENABLE and
> > SDHCI_SIGNAL_ENABLE and not rely on a previous configuration, isn't it?
>
> I imagine the card interrupt will occur when it is enabled. I don't know
> about card insert / remove.
>
> What works for you?
>

I only use wakeup events and not irqs in system PM (patches for
sdhci-of-at91 are not sent yet, I am waiting for the inclusion of other
patches).

What I mean is that if we want to wake up from irqs, it could be safer and
clearer to set explicitely SDHCI_INT_ENABLE and SDHCI_SIGNAL_ENABLE in
sdhci_enable_irq_wakeups(). It is just a thought and not needed for this
patch.

> >
> > Regards
> >
> > Ludovic
> >
> > drivers/mmc/host/sdhci.c | 26 ++++++++++++++++++--------
> > 1 file changed, 18 insertions(+), 8 deletions(-)
> >
> > diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
> > index b284924..6fc69ed 100644
> > --- a/drivers/mmc/host/sdhci.c
> > +++ b/drivers/mmc/host/sdhci.c
> > @@ -2638,18 +2638,28 @@ static irqreturn_t sdhci_thread_irq(int irq, void *dev_id)
> > \*****************************************************************************/
> >
> > #ifdef CONFIG_PM
> > +/*
> > + * To enable wakeup events, the corresponding events have to be enabled in
> > + * the Interrupt Status Enable register too. See 'Table 1-6: Wakeup Signal
> > + * Table' in the SD Host Controller Standard Specification.
> > + */
> > void sdhci_enable_irq_wakeups(struct sdhci_host *host)
> > {
> > - u8 val;
> > - u8 mask = SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE
> > - | SDHCI_WAKE_ON_INT;
> > + u8 wakeup_val;
> > + u8 wakeup_mask = SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE |
> > + SDHCI_WAKE_ON_INT;
>
> Please don't rename variables, or tidy-up code that you are not changing.
>

I thought it will be better to have wakeup_val and irq_val instead of
val and irq_val. That's why I renamed it while introducing irq_val.

> > + u32 irq_val = SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE |
> > + SDHCI_INT_CARD_INT;
> >
> > - val = sdhci_readb(host, SDHCI_WAKE_UP_CONTROL);
> > - val |= mask ;
>
> These 2 line are actually unchanged.
>
> > + wakeup_val = sdhci_readb(host, SDHCI_WAKE_UP_CONTROL);
> > + wakeup_val |= wakeup_mask;
> > /* Avoid fake wake up */
> > - if (host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION)
> > - val &= ~(SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE);
> > - sdhci_writeb(host, val, SDHCI_WAKE_UP_CONTROL);
> > + if (host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION) {
> > + wakeup_val &= ~(SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE);
> > + irq_val &= ~(SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE);
> > + }
> > + sdhci_writeb(host, wakeup_val, SDHCI_WAKE_UP_CONTROL);
> > + sdhci_writel(host, irq_val, SDHCI_INT_ENABLE);
> > }
> > EXPORT_SYMBOL_GPL(sdhci_enable_irq_wakeups);
> >
> >
>

\
 
 \ /
  Last update: 2016-05-13 14:41    [W:0.068 / U:0.048 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site