lkml.org 
[lkml]   [2016]   [May]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH V7 08/11] pci, acpi: Support for ACPI based generic PCI host controller
From
On Fri, May 13, 2016 at 1:25 PM, Jayachandran C <jchandra@broadcom.com> wrote:
> On Tue, May 10, 2016 at 8:49 PM, Tomasz Nowicki <tn@semihalf.com> wrote:
>> This patch is going to implement generic PCI host controller for
>> ACPI world, similar to what pci-host-generic.c driver does for DT world.
>>
>> All such drivers, which we have seen so far, were implemented within
>> arch/ directory since they had some arch assumptions (x86 and ia64).
>> However, they all are doing similar thing, so it makes sense to find
>> some common code and abstract it into the generic driver.
>>
>> In order to handle PCI config space regions properly, we define new
>> MCFG interface which does sanity checks on MCFG table and keeps its
>> root pointer. User is able to lookup MCFG regions based on that root
>> pointer and specified domain:bus_start:bus_end touple. We are using
>> pci_mmcfg_late_init old prototype to avoid another function name.
>>
>> The implementation of pci_acpi_scan_root() looks up the MCFG entries
>> and sets up a new mapping (regions are not mapped until host controller ask
>> for it). Generic PCI functions are used for accessing config space.
>> Driver selects PCI_ECAM and uses functions from drivers/pci/ecam.h
>> to create and access ECAM mappings.
>>
>> As mentioned in Kconfig help section, ACPI_PCI_HOST_GENERIC choice
>> should be made on a per-architecture basis.
>>
>> Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
>> Signed-off-by: Jayachandran C <jchandra@broadcom.com>
>> ---
> [....]
>
>> diff --git a/drivers/pci/ecam.h b/drivers/pci/ecam.h
>> index 1ad2176..1cccf57 100644
>> --- a/drivers/pci/ecam.h
>> +++ b/drivers/pci/ecam.h
>> @@ -45,6 +45,11 @@ struct pci_config_window {
>> void __iomem *win; /* 64-bit single mapping */
>> void __iomem **winp; /* 32-bit per bus mapping */
>> };
>> +#ifdef CONFIG_ACPI_PCI_HOST_GENERIC
>> + struct acpi_device *companion; /* ACPI companion device */
>> +#endif
>> + int domain;
>> +
>> };
>
> Using struct pci_config_window to pass along domain and
> companion looks bad. I think there are two possible options
> to do this better:
>
> 1. add a 'struct fwnode_handle *' or 'struct device *parent_dev'
> instead of the companion and domain fields above. In case of
> ACPI either of them can be used to get the acpi_device and
> both domain and companion can be set from that.
>
> 2. make pci_config_window fully embeddable by moving allocation
> out of pci_ecam_create to its callers. Then it can be embedded
> into acpi_pci_generic_root_info, and container_of can be used
> to get acpi info from ->sysdata.
>
> The first option should be easier to implement but the second may
> be better on long run. I would leave it to the Bjorn or Rafael to
> suggest which is preferred.

Personally, I'd probably try to use fwnode_handle, but the second
option makes sense too in principle.

\
 
 \ /
  Last update: 2016-05-13 13:41    [W:0.322 / U:0.408 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site