lkml.org 
[lkml]   [2016]   [May]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v7 1/5] usb: dwc3: omap: use request_threaded_irq()
From
Date
On 11/05/16 12:47, Felipe Balbi wrote:
>
> Hi,
>
> Roger Quadros <rogerq@ti.com> writes:
>>> Roger Quadros <rogerq@ti.com> writes:
>>>>>> @@ -497,8 +503,8 @@ static int dwc3_omap_probe(struct platform_device *pdev)
>>>>>> /* check the DMA Status */
>>>>>> reg = dwc3_omap_readl(omap->base, USBOTGSS_SYSCONFIG);
>>>>>>
>>>>>> - ret = devm_request_irq(dev, omap->irq, dwc3_omap_interrupt, 0,
>>>>>> - "dwc3-omap", omap);
>>>>>> + ret = devm_request_threaded_irq(dev, omap->irq, dwc3_omap_interrupt,
>>>>>> + NULL, 0, "dwc3-omap", omap);
>>>>>
>>>>> if you're using threaded_irq, it's better to have a NULL top half and
>>>>> valid bottom half.
>>>>
>>>> But in this case we don't need a bottom half as there is nothing to do :).
>>>>
>>>>>
>>>>> In fact, since this will be shared, you could do a proper preparation
>>>>> and on top half check if $this device generated the IRQ and
>>>>> conditionally schedule the bottom half. Don't forget to mask device's
>>>>> interrupts from top half so you can run without IRQF_ONESHOT.
>>>>>
>>>>
>>>> Why do this at all if there is nothing to do in the bottom half?
>>>
>>> oh, but there is :-)
>>>
>>> The whole idea of threaded IRQs is that you spend as little time as
>>> possible on top half and the (strong) recommendation is that you *only*
>>> check if $this device generated the interrupt. Note that "checking if
>>> $this device generated the interrupt" will be mandatory as soon as you
>>> mark the IRQ line as shared ;-)
>>>
>>> So here's how this should look like:
>>>
>>> static irqreturn_t dwc3_omap_interrupt(int irq, void *_omap)
>>> {
>>> struct dwc3_omap *omap = _omap;
>>> u32 reg;
>>>
>>> reg = readl(IRQSTATUS)
>>> if (reg) {
>>> mask_interrupts(omap);
>>> return IRQ_WAKE_THREAD;
>>> }
>>>
>>> return IRQ_HANDLED;
>>
>> This should be IRQ_NONE right?
>
> possibly, testing will say ;-)
>
>>> static irqreturn_t dwc3_omap_threaded_interrupt(int irq, void *_omap)
>>> {
>>> struct dwc3_omap *omap = _omap;
>>> u32 reg;
>>>
>>> spin_lock(&omap->lock);
>>
>> Do we really need a spin_lock for the dwc3-omap driver?
>> Currently we won't be doing anything other than just
>> clearing the irqstatus and re-enabling the interrupts.
>
> well, if there's no possibility of races, then no. But only testing will
> say for sure, I guess. I didn't really go through the entire thing just
> to a write a quick little template :-p
>
OK. Another hurdle I have is that how do I mask/unmask the interrupts?
I do not see any masking bits, only enable/disable bits.

I don't think we can use the enable/disable bits to mask as we'd loose
events while the event is disabled.

cheers,
-roger

\
 
 \ /
  Last update: 2016-05-11 14:01    [W:0.098 / U:0.080 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site