lkml.org 
[lkml]   [2016]   [May]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH v7 1/5] usb: dwc3: omap: use request_threaded_irq()
Date

Hi,

Roger Quadros <rogerq@ti.com> writes:
> We intend to share this interrupt with the OTG driver an to ensure
> that irqflags match for the shared interrupt handlers we use
> request_threaded_irq()
>
> If we don't use request_treaded_irq() then forced threaded irq will
> set IRQF_ONESHOT and this won't match with the OTG IRQ handler's
> IRQ flags.
>
> NOTE: OTG IRQ handler is yet to be added. This is a preparatory step.
>
> Signed-off-by: Roger Quadros <rogerq@ti.com>
> ---
> drivers/usb/dwc3/dwc3-omap.c | 12 +++++++++---
> 1 file changed, 9 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/usb/dwc3/dwc3-omap.c b/drivers/usb/dwc3/dwc3-omap.c
> index 59ea35f..6504e94 100644
> --- a/drivers/usb/dwc3/dwc3-omap.c
> +++ b/drivers/usb/dwc3/dwc3-omap.c
> @@ -272,16 +272,22 @@ static irqreturn_t dwc3_omap_interrupt(int irq, void *_omap)
> {
> struct dwc3_omap *omap = _omap;
> u32 reg;
> + int ret = IRQ_NONE;
>
> reg = dwc3_omap_read_irqmisc_status(omap);
>
> + if (reg)
> + ret = IRQ_HANDLED;
> +
> dwc3_omap_write_irqmisc_status(omap, reg);
>
> reg = dwc3_omap_read_irq0_status(omap);
> + if (reg)
> + ret = IRQ_HANDLED;
>
> dwc3_omap_write_irq0_status(omap, reg);
>
> - return IRQ_HANDLED;
> + return ret;
> }
>
> static void dwc3_omap_enable_irqs(struct dwc3_omap *omap)
> @@ -497,8 +503,8 @@ static int dwc3_omap_probe(struct platform_device *pdev)
> /* check the DMA Status */
> reg = dwc3_omap_readl(omap->base, USBOTGSS_SYSCONFIG);
>
> - ret = devm_request_irq(dev, omap->irq, dwc3_omap_interrupt, 0,
> - "dwc3-omap", omap);
> + ret = devm_request_threaded_irq(dev, omap->irq, dwc3_omap_interrupt,
> + NULL, 0, "dwc3-omap", omap);

if you're using threaded_irq, it's better to have a NULL top half and
valid bottom half.

In fact, since this will be shared, you could do a proper preparation
and on top half check if $this device generated the IRQ and
conditionally schedule the bottom half. Don't forget to mask device's
interrupts from top half so you can run without IRQF_ONESHOT.

--
balbi
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2016-05-10 12:21    [W:0.121 / U:0.108 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site